Which is the best castor tool?
Finding your suitable castor tool is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best castor tool including detail information and customer reviews. Let’s find out which is your favorite one.
Best castor tool
1. YALEEE Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment Truck Car
Feature
This adjustable equipment allows you to return the strut to the original camber position after dismantling and re-assembling the suspension or to check the amount of camber change before re-installing.Easy to read and convenient to operate
Time and money saving device
Allows adjustment to maintain correct wheel alignment and even tyre wear
SHIP FROM USA!!!
Description
CompatibleMeasures the Camber and Caster angle on the wheel hub or brake disc
Suitable for accurate checking of the castor and camber angle
Has a simple leveling adjustment from -5 degrees to 5 degrees
Magnetic gauge attaches to the hub or disc brake
Package List
1X Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment Truck Car
2. NOPTEG Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment Tool for Truck Car
Feature
There are super suction, two positioning blisters.Measure the Camber and Caster angle on the wheel hub or brake disc.Suitable for accurate checking of the castor and camber angle.
Has a simple leveling adjustment from -5 degrees to 5 degrees
Magnetic gauge attaches to the hub or disc brake.Allows adjustment to maintain correct wheel alignment and even tyre wear
Allows you to return the strut to the original camber position after dismantling and re-assembling the suspension or to check the amount of camber change before re-installing
Description
Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment
Instructions
1, remove the four wheel positioning sensor (fixture) and unload the tires.
2. Absorb the magnetic level carefully on the side of the brake wheel.
3, adjust the level to zero.
4, install the required special parts for positioning;
5. Use a special tool to adjust the positioning parts to the required angle of measurement with the aid of the degree indicator of the magnetic level.
6. If a few deviations are found with a locator retest, it is only necessary to tune in the bottom of the car. (generally a few deviations do not cause a location fault)
NOTE
1.As different computers display colors differently, the color of the actual item may vary slightly from the above images.
2. Please allow 1-3 CM differs due to manual measurement.
3. Hanperal Universal Magnetic Gauge Tool for Car/Truck Camber/Castor Strut Wheel Alignment
Feature
Easy to read and convenient to operateThere are super suction, two positioning blisters
Suitable for accurate checking of the castor and camber angle
Has a simple leveling adjustment from -5 degrees to 5 degrees
It's allows you to return the strut to the original camber position after dismantling and re-assembling
Description
Feature:1.Time and money saving device.
2.Weight: 256g/9.14oz
3.Measures the Camber and Caster angle on the wheel hub or brake disc.
4.Has a simple leveling adjustment from -5 degrees to 5 degrees.
5.It's allows to adjustment to maintain correct wheel alignment and even tyre wear.
6.This adjustable equipment allows you to return the strut to the original camber position after dismantlingThis adjustable equipment allows you to return the strut to the original camber position after dismantling and re-assembling the suspension or to check the amount of camber change before re-installing.
Instructions for use:
1. Remove the wheel alignment sensor (Clip tool), remove the tire;
2, The magnetic level gauge carefully on the side of the suction wheel disc brakes;
3, the water level was adjusted to zero;
4, install the required location specific parts;
5, use a special tool, with the degree of magnetic level gauge indication, adjust the positioning of the part to the desired measurement angle.
6, retest with locator If there is a little deviation, just to fine-tune the vehicle. (Usually a slight deviation does not cause fault location)
4. KIPA Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment Tool for Truck Car RV Tire Repair
Feature
This adjustable gauge allows you to return the strut to the original camber position after dismantling and re-assembling the suspension or to check the amount of camber change before re-installing. Measures the Camber and Caster angle on the wheel hub or brake disc. Suitable for accurate checking of the castor and camber angleWheel Alignment tool
Universial Automotive Tool For Wheel Alignment
It has a powerful magnet could be easily mounted on all kinds of metal surface.(Note:Please double check and make sure the panel is balance before using.You could screw the button behind the gauge to adjust panel level)
The body of gauge is made of high density aluminum and precision level vial, but the mount is made of metal so that please live it away from water, or maybe it will get rusty
Description
This is An adjustable equipment allows you to return the strut to the original camber positionafter dismantling and re-assembling the suspension or to check the amount of camber change before re-installing.
In-Kind Shooting
Specification:
Measures the Camber and Caster angle on the wheel hub or brake disc
Suitable for accurate checking of the castor and camber angle
Has a simple leveling adjustment from -5 degrees to 5 degrees
Magnetic gauge attaches to the hub or disc brake
Allows adjustment to maintain correct wheel alignment and even tyre wear
Time and money saving device
Easy to read and convenient to operate
Simple Instruction:
How to use:
1. Remove the wheel alignment sensor (Clip tool), remove the tire;
2, The magnetic level gauge carefully on the side of the suction wheel disc brakes;
3, the water level was adjusted to zero;
4, install the required location specific parts;
5, use a special tool, with the degree of magnetic level gauge indication, adjust the positioning of the part to the desired measurement angle.
6, retest with locator If there is a little deviation, just to fine-tune the vehicle. (Usually a slight deviation does not cause fault location)
Simple Reminder:
If you need very detailed adjustment instruction, You may search "wheel alignment tool" on youtube. There are some video
5. 621PCS Tool Aluminum Case Tools Set With Trolley Standard Metric Hand Tool Kit with Case Box Organize Castors Trolley
Feature
Outstanding Durability and Strength - Premium carbon steel tools & Aluminum trolley & Long service lifeWide Usage - Mechanics tool sets include high value hand tools for both the professional and do-it-yourself worker
Contents - quantity choices 621pcs and Case Box Organize Castors Trolley with 2 pairs gloves as gift
Easy Maintenance - Full polished chrome finish for anti-corrosion protection and convenience cleaning of oil and dirt
Overall dimensions- 20.5*8.7*14.96 inchesDetachable pull rod.
Description
Layer A1pc insulation screwdriver 5.5*125-
2pc insulation screwdriver 4*100
2pc screwdrivers 6*38
2pc screwdrivers 3*75
2pc screwdrivers 4*100
2pc screwdrivers 5*75
2pc screwdrivers 6*100
1pc screwdriver 8*150+
1pc ratchet wrench
6pc precision screwdrivers 1,1.5,2,2.5,3,3.5 48pc bits
1pc pressure gauge
16pc hex key
1pc tester 1extension bar 58L
Layer B
1pc insulation tape
1pc 8"stripping wire plier
1pc scissors
1pc glue gun
2pc glue
1pc measruing tape
1pc utility knife
1pc 12oz claw hammer
2pc nylon clamp
12pc bits
10pc blade
1pc level 250mm
136pc hardware box
Layer C
1pc rachet wrench 1/4"
1pc rachet wrench 1/2"
1pc sockets holder
1pc 1/4"flexible extension bar 6"
1pc 1/4" extension bar 4"
1pc 1/4" extension bar 2
Layer D
9pc combintation
wrench:6,8,10,11,12,13,14,15,17mm
1pc 6"side cutting plier
1pc long nose plier
1pc 9"water pump plier
1pc 6"adjustable wrench
1pc 6" joint plier
300pc cable ties
2pc gloves
6. Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment Truck Car US
Feature
The Magnetic Gauge Tool measures the Camber and Caster angle on the wheel hub or brake disc.Suitable for accurate checking of the castor and camber angle.
Has a simple leveling adjustment from -5 degrees to 5 degrees.
Allows adjustment to maintain correct wheel alignment and even tyre wear
Magnetic gauge attaches to the hub or disc brake
Description
Instructions for use:1. Remove the four-wheel positioning sensor (fixture), remove the tire
2. Carefully suck the magnetic gauge tool on the side of the brake wheel
3. Adjust the gauge tool to zero
4. Installed the required positioning special parts
5. Use special tool, with the help of magnetic gauge tool's degree instruction to adjust the positioning parts to the required measurement angle
6. If there is a little deviation when re-test with the positioning tool, just fine-tune at the bottom of the car. (Generally a little deviation does not cause positioning failure)
7. Granit Adjustable Magnetic Gauge Tool Camber Castor Strut Wheel Alignment Tool for Truck Car RV Tire Repair
Feature
1.This adjustable gauge allows you to return the strut to the original camber position after dismantling and re-assembling the suspension or to check the amount of camber change before re-installing. Measures the Camber and Caster angle on the wheel hub or brake disc. Suitable for accurate checking of the castor and camber angle.2.It has a powerful magnet could be easily mounted on all kinds of metal surface.(Note:Please double check and make sure the panel is balance before using.You could screw the button behind the gauge to adjust panel level)
3.Also it could be used as a normal gradienter (Magnetic mount could be released).
4.Size: 4.5''*1.2''*0.8'' It has a simple leveling adjustment from -5 degrees to 5 degrees
5.The body of gauge is made of high density aluminum and precision level vial, but the mount is made of metal so that please live it away from water, or maybe it will get rusty.
Description
Thank you very much for choosing our product! Toe angle, camber angle(or inclination),scrub radius, caster angle, mechanical trail, kingpin angle, kingpin offset are very important performances to adjust the chassis of your car. This gauge could help you ensure if you have got the correct camber angle and caster angle. Also it could be used as a normal gradienter. The body of gauge is made of high density aluminum and precision level vial, but the mount is made of metal so that please live it away from water, or maybe it will get rusty.8. MaxxHaul 80748 Rolling Knee Creeper/Pads with ABS High-Impact Frame, 5 Swivel Castors, Tool Tray and Holder
Feature
Rolling knee pads allow you to be mobile and easily move from side to side while protecting your knees.Frame is made from rugged ABS high impact plastic with pads to cushion your knees while performing your project.
Features five 2" diameter non-marring swivel castors for maximum maneuverability.
Built-in tray and holder to keep your small tools and parts handy
Perfect when doing painting, laying tile or vinyl, Auto Detailing, Auto repair & maintenance, landscaping and more
Description
Our MaxxHaul rolling knee pads allow you to be mobile while protecting your knees. Frame is made from rugged ABS high impact plastic with pads to cushion your knees while performing your project. Perfect when doing painting, laying tile or vinyl, auto detailing, auto repair & maintenance, landscaping and more. Includes a conveniently placed built-in tray and holder to keep your tools and parts handy. Maximum 250 lbs. Capacity with five 2" diameter non-marring swivel castors for easy maneuverability. Allows movement from side to side making tiling comfortable and easy. Minimize discomfort, back pain or knee stress.9. Agile-Shop Universal Magnetic Gauge Tool For Car/Truck Camber Castor Strut Wheel Alignment
Feature
Magnetic gauge the Camber and Caster angle on the wheel hub or brake discSuitable for accurate checking of the castor and camber angle
Has a simple leveling adjustment from -5 degrees to 5 degrees
With two positioning blisters
Allows adjustment to maintain correct wheel alignment and even tyre wear
Description
Feature:This adjustable equipment allows you to return the strut to the original camber position after dismantling and re-assembling the suspension or to check the amount of camber change before re-installing.
Time and money saving device.
Easy to read and convenient to operate.
Package Content:
1 x Magnetic Alignment Camber Castor Gauge
How to use:
1. Remove the wheel alignment sensor (Clip tool), remove the tire;
2, The magnetic level gauge carefully on the side of the suction wheel disc brakes;
3, the water level was adjusted to zero;
4, install the required location specific parts;
5, use a special tool, with the degree of magnetic level gauge indication, adjust the positioning of the part to the desired measurement angle.
6, retest with locator If there is a little deviation, just to fine-tune the vehicle. (Usually a slight deviation does not cause fault location)
10. SUNCOO 710 Pieces Tool Kit Standard Metric Mechanics Set Case Box Organize Castors Trolley (Black Case)
Feature
Wide Usage - Rolling tool set includes high value hand tools for both the professional and do-it-yourself worker.Easy to Carry & Storage-Portable tool box not only offers the easy transport but also provides a orderly tools storage. Durable wheels and telescopic handle make it easy to carry and stock, you can put the tool case in the any place you go.
Easy Maintenance - Full polished chrome finish for anti-corrosion protection and convenience cleaning of oil and dirt.
Outstanding Durability and Strength - Premium carbon steel tools & Aluminum trolley & Long service life.
Tool Kit with Case:overall dimensions - 15.0*8.7*20.5 inches&Weight: 29 lbs
Description
This 710 pieces tool set mechanics kit satisfies your needs and demands usage.
Contents:
Tray A:
- 3 x insulation screwdrivers
- 11 x screwdrivers
- 1 x ratchet bits holder
- 6 x precision screwdriver
- 24 x bits
- 9 x hex key
- 1 x tester
- 1 x pickup
- 1 x bit extension bar
Tray B:
- 1 x insulation tape
- 1 x wire stripping pliers
- 1 x scissor
- 1 x electric glue gun
- 2 x glue stick
- 1 x measuring tape
- 1 x utility knife
- 1 x claw hammer
- 2 x nylon clip 3''
- 1 x aluminum level
- 78 x fastener
Tray C:
- 2 x ratchet wrenches
- 1 x sockets holder
- 1 x 1/4'' flexible extension bar
- 2 x 1/4'' extension bar
- 1 x 1/4'' universal joint
- 1 x 1/4'' slipping bar
- 15 x 1/4'' sockets
- 2 x 1/2'' spark plug sockets
- 1 x 1/2'' universal joint
- 2 x 1/2'' extension bar
- 14 x 1/2''sockets
Try D:
- 9 x combination wrench
- 1 x side cutting plier
- 1 x long nose plier
- 1 x water pump plier
- 1 x adjustable wrench
- 1 x joint plier
- 1 x gray case with black cornered
- 4 x PE blow case with shrink wrapping
- 500 x cable ties 2.5*100mm
- 2 x gloves
Recent Comments