Where to find pins knife?
When you looking for pins knife, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable pins knife is not an easy task. In this post, we show you how to find the right pins knife along with our top-rated reviews. Please check out our suggestions to find the best pins knife for you.
Best pins knife
1. 360 Brass Knife Pin Stock 3/16" x 6 inch 2pcs.
Description
360 Brass Knife Pin Stock 3/16" x 6 inch 2pcs. Designed for use in making knives.2. Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (3/16") (#23 (3/16"))
Feature
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.Diameter: 3/16", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Description
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
3. Swpeet 21Pcs Metal Round Rods Kit, 3 Kinds of Metal Materials Including Stainless Steel, Brass and Aluminum Perfect for for DIY Craft Tool - Diameter 2mm-8mm Length 100mm
Feature
GOOD QUALITY --- These are good quality metal. They came wrapped in plastic box so there was no way for oxidization to occur and stain the pins. All 10 pins are a uniform size and finish and take a polish very well after installing in a knife handle.WIDE APPLICATIONS --- These rods can be cut and formed into replacement parts for almost anything, you are only limited by your imagination. Widely used in Gear shaft, motor shaft, short support shaft, shaft pocket model, miniature axle, model plane, model ship, model cars.
EASY TO CUT--- These things are very nice and easy to cut. You can cut to any size you want according to your needs. They are the correct length and diameter and will be worth for the price.
PRODUCT INFORMATIONS --- Color: Golden and Sliver; Material: Brass, Stainless steel, Aluminum ; Size: 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm. Length: 100mm.
WHAT YOU GET --- We have prepared high quality 21pcs different material Metal rods for you, These different material metal rods canto meet any of your needs and you deserve them. Don't wait, order it now.
Description
Swpeet 21Pcs Metal Round Rods Kit, 3 Kinds of Metal Materials Including Stainless Steel, Brass and Aluminum Perfect for for DIY Craft Tool--Diameter 2mm-8mm Length 100mmSpecifications
Color: Golden, Silver
Materials: Brass, Stainless Steel, Aluminum
Diameter: 2mm, 2.5mm,3mm, 4mm, 5mm, 6mm, 8mm
Length: 100mm
Package included:
Brass Rods:
1x 2mm Brass rods
1x 2.5mm Brass rods
1x 3mm Brass rods
1x 4m Brass rods
1x 5mm Bbrass rods
1x 6mm Brass rods
1x 8mm Brass rods
Stainless Steel Rods:
1x 2mm Stainless steel rods
1x 2.5mm Stainless steel rods
1x 3mm Stainless steel rods
1x 4m Stainless steel rods
1x 5mm Stainless steel rods
1x 6mm Stainless steel rods
1x 8mm Stainless steel rods
Aluminum Rods:
1x 2mm Aluminum rods
1x 2.5mm Aluminum rods
1x 3mm Aluminum rods
1x 4m Aluminum rods
1x 5mm Aluminum rods
1x 6mm Aluminum rods
1x 8mm Aluminum rods
Total 21 Metal rods
Note: 1. Please allow 1-5mm error due to manual measurement. 2. As the lighting effects, the color of objects maybe a little different from pictures.
4. 5 Pack of 3/16" Diameter Micarta Canvas Knife Handle Pins, 12" Black Rod
Feature
Micarta is tough, durable, resistant to corrosion, acids, oils, heat, cold, moisture, compression, and impact.Proudly made in the United States. Great gift for your custom knives craftsman!
Five pack of micarta rods
Each rod is 12" long and 3/16" in diameter
Blends perfectly with Black Canvas Micarta knife handle scales
Description
Knife pins hold the scales to the tang, and are an integral part of nearly every knife's handle. While many knives use standard stainless steel pins, sometimes you want your workmanship to blend in, and our canvas Micarta pins help you do just that!5. Mosaic Pin 1cm Knife Making Jewelry Handle Scales Grips Knives (#108 Elk-Brass)
Feature
NOTICE: Read the "Important Instructions" section below.Diameter: 1cm (approximately 25/64 inches)
Length: 10cm (4 inches)
This pin is made from brass.
Description
It can be used as a solid pin or sliced into thin pieces for inlays. The pattern exists along the entire pin length.
Important Instructions:
- This pin requires a hole of 1cm to be drilled into the handle of your knife. You simply need to use drill bits intended for drilling metal, which are capable of drilling through the steel type of your blade (i.e. hardened 1095 high carbon steel, D-2, stainless, etc).
- Do not expose to excessive heat when cutting the pins (it will become damaged over 95 degrees celsius). Do not polish them too much.
- Use only sandpaper for polishing. Use 1200 grit sandpaper for final polishing.
- And last, use lacquer or oil.
- Outside Diameter: 1cm (equal to 10mm) (approximately 25/64 inches)
- Length: 10cm (4 inches)
- The center of the mosaic pin is filled with epoxy resin.
6. Five Pack of 1/8" Diameter Solid Brass Knife Handle Rod, 12" Length
Feature
Solid brass knife handle rods proudly made in the USA!Can be polished to a mirror finish
Complements your brass bolster, guard, or pommel
Rod is 12" long and 1/8" in diameter
NOTE ON SHIPPING: All orders from Texas Knifemakers Supply are shipped USPS Priority Mail (2-3 business day delivery) with a tracking number. Order multiple items to combine on shipping and save!
Description
Knife pins hold the scales to the tang, and are an integral part of nearly every knife's handle. These brass pins are made in the USA, and complement your brass bolster or guard. You can purchase brass barstock here: http://www.amazon.com/Brass-Barstock-Knife-Guards-Bolsters/dp/B017ROMGU8/7. Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (1/4") (#63 (1/4"))
Feature
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.Diameter: 1/4", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Description
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
8. Mosaic - USA KMS Mosaic Pin for Knife Handle 1/4" x 11" Brass #117-1
Feature
Style #117-1Brass Tube with Stainless Steel Rod and Star Design
Use these mosaic pin/lanyard tubes in your knife handles to give some extra detail.
Description
Tip: These get hot very quickly when being worked and the epoxy will soften or worse break down. This is just the nature of mosaic tubing. Keep them cool when you getting them to length or working them in your handle. Cut or grind them with fresh blade or belt. Dip frequently if you need to.9. Swpeet 15Pcs 3mm Diameter 100mm Length Brass Solid Round Rod Lathe Bar Stock, Perfect for Various Shaft, Miniature Axle, Model Plane, Model Ship, Model Cars
Feature
GOOD QUALITY --- These are good quality brass pins. They came wrapped in plastic box so there was no way for oxidization to occur and stain the pins. All 10 pins are a uniform size and finish and take a polish very well after installing in a knife handle.WIDE APPLICATIONS --- These rods can be cut and formed into replacement parts for almost anything, you are only limited by your imagination. Widely used in Gear shaft, motor shaft, short support shaft, shaft pocket model, miniature axle, model plane, model ship, model cars.
EASY TO CUT--- These things are very nice and easy to cut. You can cut to any size you want according to your needs. They are the correct length and diameter and will be worth for the price.
PRODUCT INFORMATIONS --- Color: Golden ; Material: Brass ; Standard Size: 100mm x 3mm /4" x 0.1.2"(L*D).
WHAT YOU GET --- We have prepared 15pcs high quality brass rods for you to meet any of your needs and you deserve them. Don't wait, order it now.
Description
Specifications:Material: brass
Color: golden
Length: 100mm
Diameter: 3mm
Package included:
15x 3mm brass rods
Features:
-For DIY craft making.
-Sturdy and durable.
Notice:
1. As the lighting effects, the color of objects maybe a little different from pictures.
2. Please allow 1-5mm error due to manual measurement.
please make sure you do not mind before you bid.
Recent Comments