Top recommendation for smoke tester for cars
Finding your suitable smoke tester for cars is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best smoke tester for cars including detail information and customer reviews. Let’s find out which is your favorite one.
Best smoke tester for cars
1. AUTOOL SDT-206 Automotive Car Vehicle Boat Conduit Pipe System Car PIPE Leakage Tester Car Fuel Leak Detector SDT206 Automotive Fuel leakage Diagnostic Tester Adjustable Flowmeter
Feature
🌹 This machine will detect the leakage of pipe systems on cars, motorcycles, boats...such as fuel pipe, air intake system and cooling tank.🌹The machine will change special oil into smoke, then blow smoke into sealed pipe system. you will find leak point in pipe via the smoke.
🌹This upgraded machine now can work on EVAP system (pressure of machine was larger than EVAP request )
🌹Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload. Combine with adjustable flowmeter and pressure guage,we can adjust output of smoke ,then check leakage level via smoke flow variety
🌹Input :12V DC ; Smoke output value: 6L/min, We offer technical support if needed.
Description
Operation
1.Open the engine cover, and hang the detector in the cover.
2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle. Please secure the other side with a rubber stopple.
3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts to work.
6.Adjust the flow gauge. Control the input smoke value and pressure to make sure the pipe system can afford the pressure.
7.In about 3 minutes, the pipe will be filled with smoke.
8.Observe the floating ball in flow gauge. If the floating ball stays still in the bottom, the pipe is sealed with. If the floating ball is arising or bouncing, the pipe is leaking.
9.Position the leak points by floating ball. If the bounce arises highly, the leakage is serious.
10.Check the leak points. Please use head lamp if necessary.
11.After leak detection, please connect well the wires and pipe.
Do not run the detector over 5 minutes. It needs interval rest.
The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later.
Maintenance
With longtime high temperature, the smoke and oil will oxidize and deteriorate. It will infect the service life of smoke generated part, so please change smoke and oil regularly.
1.Before filling new oil, please pour out the remaining oil in the detector.
2.When the smoke output has water drops, please replace with new oil.
3.Liquid paraffin and baby oil are OK. Please fill new oil with equipped oil bott
2. AUTOOL SDT-106 Automotive Fuel Leak Detectors Car Pipe Leakage Tester SDT106 Cars Leak Locator Automotive Diagnostic Leak Tools for 12V Vehicles
Feature
🌹SDT-106 is designed for detecting the leakage of pipe systems on cars, motorcycles, such as fuel pipe, air intake system and cooling tank. SDT-106 is for all pipe systems Support EVAP.🌹Hook: To hang the detector when detecting Working Indicator: It is lit when the detector works
🌹Power Switch: Power it on, and the detector works
🌹Smoke output tube: The smoke outlet which connecting with detection port
🌹Power clip: To connect with vehicle battery. The voltage is DC12V.
Description
Cautions:
1.When you use this detector the first time, please fill 20-30ml oil, not beyond this range.
2.New oil can be filled with only when the smoke is light,and it can't be filled over 15ml every time.
3.Before filling new oil, please pour out the remaining oil in the detector.
4.Please replace the detector oil regularly.
Operation
1.Open the engine cover, and hang the detector in the cover.
2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle. Please secure the other side with a rubber stopple.
3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts to work.
6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary.
7.After leak detection, please connect well the wires and pipe.
* Do not run the detector over 8 minutes. It needs interval rest.
* The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later.
* The round parts of this detector is with temperature, be careful to avoid scalding injury.
Maintenance
With longtime high temperature, the smoke and oil will oxidize and deteriorate. It will infect the service life of smoke generated part, so please change smoke and oil regularly.
1.Before filling new oil, please pour out the remaining oil in the detector.
2.When the smoke output has water drops, please replace with new oil.
3.Liquid paraffin and baby oil are OK.
4.Please fill new oil with equipped oil bottle
3. OTC (6522 LeakTamer EVAP Smoke Diagnostic Machine
Feature
80 percent of top codes can be diagnosed with smoke technologyUltraTrace UV dye is the only OE approved solution
New smoke flow control adjusts for specific applications
Detects micro leaks to and below .010 inch
Unit is half the size of its predecessor but twice as mighty with more powerful features
Description
The OTC 6522, at least 80 percent of the top emission codes on vehicles today can be diagnosed faster and more accurately with smoke technology. Technicians proficient with engine maintenance, vacuum, gaskets and seals including EVAP systems have a multitude of problem finding opportunities using the smoke based leak detection offered by OTC's LeakTamer. And when working on EVAP systems, you need more than just a scan tool. The LeakTamer is less than half the size of its popular predecessor model offering improved portability in your shop and more powerful diagnostics in a smaller package. General repair and body shop technicians can use this tool to solve problems including wind noise, heating, ventilation and air-conditioning (HVAC) performance, or to locate and repair water drainage issues. The OTC LeakTamer incorporates patented technology by introducing an OEM approved smoke compound with UltraTrace UV dye to locate virtually any kind of leak quickly and easily. This tool helps technicians and shop owners save money by eliminating wasted time. A leak as small as 0.020 inch in diameter can allow more than 30 times the amount of hydrocarbons into the atmosphere than is currently acceptable through the exhaust. The LeakTamer can detect micro leaks down to and below 0.010 inch with its large, easy-to read flow meter. The unit also includes precise flow control which is a powerful new feature that allows the operator to adjust amount of smoke the LeakTamer puts out. This helps pinpoint leaks faster and more efficiently, minimizing customer comebacks and improving service bay productivity. This kit contains the LeakTamer unit, white/UV combination with laser pointer, UV glasses for viewing UltraTrace UV dye, service port adapter, exhaust adapter cone, cap plug adapters, Schrader removal/installation tool, and an 8 ounce UltraTrace UV smoke producing solution.4. AUTOOL SDT-202 Automotive Fuel Leak Detector 12V Car Leak Locator Tester Support EVAP Car Fuel Leak Detector SDT202 Car Pipe Leak Tester for All Vehicle
Feature
SDT-202 Fuel leak Detector for all pipe systems Support EVAP system with specific adapter in the package. Power supply is DC 12V by vehicle battery.SDT-202 Car Leak Locator tester is designed for detecting the leakage of pipe systems on cars, motorcycles, such as fuel pipe, air intake system and cooling tank.
SDT-202 Car Fuel Leak Detector Input: 12V DC ; Smoke output value: 6L/min, simple operation and quick locator the leak part.
SDT-202 Car Pipe Leak Tester built-in air compressor, Instant smoke generation. Self-protective system will keep machine away from overload
SDT-202 Car Pipe leak Detector will change special oil(baby oil or mineral oil) into smoke, then blow smoke into sealed pipe system. You will find leak point in pipe via the smoke. Please repair the part where leak exists.
Description
How to Use:
1. Open the engine cover, and hang the detector in the cover.
2. Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle. Please secure the other side with a rubber stopple.
3. Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4. Connect detector with DC 12V battery: red with positive, black with negative. Do not connect in a contrary way.
5. Turn on the power switch, and detector starts to work.
6. In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary.
7. After leak detection, please connect well the wires and pipe.
* Do not run the detector over 8 minutes. It needs interval rest.
* The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later.
* The round parts of this detector is with temperature, be careful to avoid scalding injury.
Cautions:
1. When you use this detector the first time, please fill 20-30ml oil, not beyond this range.
2. New oil can be filled with only when the smoke is light, and it can't be filled over 15ml every time.
3. Before filling new oil, please pour out the remaining oil in the detector.
4. Please replace the detector oil regularly.
Package List:
Main Unit
Hook
Rubber stopples
Taper stopple
Taper pipe
30ml oil bottle
User manual
5. AUTOOL 12V Automotive Fuel Leak Detectors SDT-202 Cars Leak Locator Tester Car Fuel Leak Detectors SDT202 Car PIPE Leakage Tester Support EVAP For All Vehicles
Feature
🌹SDT-202 is designed for detecting the leakage of pipe systems on cars, motorcycles, such as fuel pipe, air intake system and cooling tank.🌹SDT-202 is for all pipe systems Support EVAP EVAP system with specific adapter in the package, Power supply is DC12V by vehicle battery
🌹Input :12V DC ; Smoke output value: 6L/min, simple operation and quick locator the leak part.
🌹Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload
🌹The machine will change special oil(baby oil or mineral oil) into smoke, then blow smoke into sealed pipe system. you will find leak point in pipe via the smoke. Please repair the part where leakage exists.
Description
Cautions:
1.When you use this detector the first time, please fill 20-30ml oil, not beyond this range.
2.New oil can be filled with only when the smoke is light,and it can't be filled over 15ml every time.
3.Before filling new oil, please pour out the remaining oil in the detector.
4.Please replace the detector oil regularly.
How to Use:
1.Open the engine cover, and hang the detector in the cover.
2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle. Please secure the other side with a rubber stopple.
3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts to work.
6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary.
7.After leak detection, please connect well the wires and pipe.
* Do not run the detector over 8 minutes. It needs interval rest.
* The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later.
* The round parts of this detector is with temperature, be careful to avoid scalding injury.
Package List:
1.Main Unit
2.Hook
3.Rubber stopples
4.Taper stopple
5.Taper pipe
6.30ml oil bottle
7. User manual
6. AUTOOL Vehicle Boat Conduit Pipe System Smoke Leak Detecting Tester Diagnostic Machine with Flowmeter Pressure Guage
Feature
This machine will detect the leakage of pipe systems on cars, motorcycles, boats...such as fuel pipe, air intake system and cooling tank.The machine will change special oil into smoke, then blow smoke into sealed pipe system. you will find leak point in pipe via the smoke.
This upgraded machine now can work on EVAP system with specific adapter (pressure of machine was larger than EVAP request )
Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload. Combine with adjustable flowmeter and pressure guage,we can adjust output of smoke ,then check leakage level via smoke flow variety
Input :12V DC ; Smoke output value: 6L/min, We offer technical support if needed.
Description
Please Notes:
1 Avoiding test smoke-sensitive parts with this machine.
2 The machine can work on EVAP system with specific adapter (pressure of machine was larger than EVAP request ).
3 Don't work with the machine continuously more than 8 minutes.Bottom of the machine will give out heat,be careful!
4 Injection paraffin oil or baby oil in machine before detecting (oil is not included in the pack)
How to change oil?
A There are 2 oil bottles come with machine, please injection oil with that bottle.
B Injection 20-30ml oil in the machine when use it in the first time.
C When smoke become weak or go out with steam, it means we should change oil, release residue then injection new oil in machine ( don't more than 15ml )
How to use?
1.Open the engine cover, and hang the detector on the cover.
2. Blocking one side of pipe with end cap, the other side should blocked with taper plug. Connecting machine with taper plug.
3.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
4.Turn on the power. Adjust smoke flow and pressure to fit for the pipe system.
5.About 3 minutes later, the pipe will be filled with smoke. We can check leak points via smoke.
6. Please use flashlight and endoscope to review the leakage if it is necessary
Package Include.
1x Main Unit1x Main Unit
1x.Hook (with hand-tighten nuts)
1x End cap kits
1x Taper plug
1x Taper pipe
1x Air Sac
2x Oil bottle
1x User manual
7. MRCARTOOL T110 Automotive Fuel Leak Detectors Car Pipe Leakage Tester Car Leak Locator Automotive Diagnostic Leak Detector Support EVAP For Motorcycle/Cars/SUVs/Trucks/Boats
Feature
🌹T110 is designed for detecting the leakage of pipe systems on cars, motorcycles, such as fuel pipe, air intake system and cooling tank. T110 is for all pipe systems Support EVAP.Support AIR SYSTEM on cars.🌹Hook:To hang the detector when detecting Working Indicator: It is lit when the detector works
🌹Power Switch: Power it on, and the detector works
🌹Smoke output tube: The smoke outlet which connecting with detection port.
🌹Power clip: To connect with vehicle battery. The voltage is DC12V.
Description
MR CARTOOL T110 Car Smoke Maker is designed for detecting the leakage of pipe systems on cars, motorcycles, such as fuel pipe, air intake system EVAP system and cooling tank. Connecting leakage detector to pipe system, Inject baby oil into detector and produce smoke with it. Once there is smoke blow out in somewhere of pipe system, that is the leakage point
Kindly Note:
1. Please inject 20-30ml baby oil when you use it in the first time
2. Add more baby oil when smoke go fade, it should less than 15ml every time
3. Please drain out all the rest before adding new baby oil
Parameter:
Power: DC12V, vehicle battery
Smoke output value: 6l/min
Built-in air supply
Controllable flow value
How to use:
1.Open the engine cover, and hang the detector on cover.
2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle.
Please secure the other side with a rubber stopple.
3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts to work.
6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary.
7.After leak detection, please connect well the wires and pipe.
8.Notes:
* Please do leak detection away from smoke-sensitive parts.
* Do not run the detector over 8 minutes. It needs interval rest.
* The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later.
* The round parts of this detector is with temperature, be careful to avoid scalding injury.
8. OUERKEJI Car Vehicle Boat Smoke Leak Detecting Tester,Car Fuel Leak Detector with Flowmeter Pressure Guage for Vehicle Boat Conduit Pipe System Automotive Diagnostic Machine
Feature
Input :12V DC ; Smoke output value: 6L/min, work on EVAP system (pressure of machine was larger than EVAP request )Detect the leakage of pipe systems on cars, motorcycles, boats...such as fuel pipe, air intake system and cooling tank.
Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload. Combine with adjustable flowmeter and pressure guage,we can adjust output of smoke ,then check leakage level via smoke flow variety
Change special oil into smoke, then blow smoke into sealed pipe system. It can find leak point in pipe via the smoke.
With longtime high temperature, the smoke and oil will oxidize and deteriorate. It will infect the service life of smoke generated part, so please change smoke and oil regularly. If you have any question ,please contact us in time.We offer technical support if needed.
Description
HOW TO USE: Open the engine cover, and hang the detector in the cover.
Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
Turn on the power switch, and detector starts to work.
Adjust the flow gauge. Control the input smoke value and pressure to make sure the pipe system can afford the pressure.
In about 3 minutes, the pipe will be filled with smoke.
Please use flashlight and endoscope to review the leakage if it is necessary
After leak detection, please connect well the wires and pipe.
Car Vehicle Boat Smoke Leak Detecting Tester NOTES: The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later.
The machine can work on EVAP system with specific adapter (pressure of machine was larger than EVAP request ).
Avoiding test smoke-sensitive parts with this machine.
Don't work with the machine continuously more than 8 minutes.Bottom of the machine will give out heat,be careful!
Injection paraffin oil or baby oil in machine before detecting (oil is not included in the pack)
HOW TO CHANGE OIL: 1,There are 2 oil bottles come with machine, please injection oil with that bottle.
2,Injection 20-30ml oil in the machine when use it in the first time.
3,When smoke become weak or go out with steam, it means we should change oil, release residue then injection new oil in machine ( don't more than 15ml )
Car Vehicle Boat Smoke Leak Detecting Tester Package Include: 1x.Hook (with hand-tighten nuts)
1x Main Unit
1xTaper plug
1x End cap kits
1x User manual
1xTaper pipe
2x Oil bottle
9. AUTOOL 12V Automotive Fuel Leak Detector Car Pipe Leak Locator Machine Support Pipe Systems/Motorcycle/Cars/SUVs/Boat with Pressure Gauge
Feature
Professional machine will detect the leakage part of pipe systems on cars, motorcycles, boats, such as fuel pipe, air intake system and cooling tank easilyThe machine will change special oil(baby oil or mineral oil) into smoke, then blow smoke into sealed pipe system. you will find leak point in pipe via the smoke. Please repair the part where leakage exists.
This upgraded machine now can work on EVAP system with specific adapter in the package, Power supply is DC12V by vehicle battery
Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload
Input :12V DC ; Smoke output value: 6L/min, simple operation and quick locator the leak part.
Description
How to use?
1.Open the engine cover, and hang the detector in the cover.
2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle, please secure the other side with a rubber stopple.
3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts to work.
6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary.
7.After leak detection, please connect well the wires and pipe.
8. Please repair the leak part timely with specific tool.
Hook: To hang the detector when detecting
Working Indicator: It is lit when the detector works
Power Switch: Power it on, and the detector works
Smoke output tube: The smoke outlet which connecting with detection port
Power clip: To connect with vehicle battery. The voltage is DC12V.
Pressure gauge: To show the working pressure
Package Includes
1* Main Unit
1* Hook (with hand-tighten nuts)
1* Rubber stopples (with serial specification)
1* Taper stopple
1* Taper pipe
1* 30ml oil bottle
10. AUTOOL SDT-202 Car EVAP System Leak Testing Machine Leak Detector, 12V Automotive Fuel Pipe System Leak Tester with EVAP Adapters for All Vehicles - 3 Years Warranty
Feature
WORKING PRINCIPLE -- The Smoke Machine heat up special oil(mineral oil or baby oil) into smoke and blow smoke into sealed pipe system. You will find out leak point in pipe in where has smoke. Please repair the part where leakage exists.CONVENIENT TOOL FOR MACHANICS -- The SDT-106 is a simple-using Smoke Machine for techs to detect the leakage of pipe systems on cars, motorcycles, such as fuel pipe, air intake system and cooling tank.
EVAP SYSTEM SUPPORTED -- Comes with EVAP adapters, SDT-106 can help you apply with EVAP System of all vehicles to quickly find out the leak parts. 4ft Smoke Outlet Pipe can help reach and connect perfectly.
SPECIFICATIONS -- Voltage: DC 12V(Supplied by Automotive Battery). Smoke Output Value: 10-15L/min. Output Pressure: 10-13PSI. Heating Material: Mineral Oil or Baby Oil. Multi Protections: Over-heat & Over-load Protection.
3 YEARS WARRANTY -- 3-7days fast shipment via DHL. To ensure your high-quality shopping experience, we provide 3 years warranty(longer than competing machines). 24 hours E-mail supports can help resolve any issues of using. Buy and use with confidence.
Description
Ways of Use:1.Open the engine cover, and hang the detector in the cover.
2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle, please secure the other side with a rubber stopple.
3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts to work.
6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary.
7.After leak detection, please connect well the wires and pipe.
8. Please repair the leak part timely with specific tool.
Features:
Hook: To hang the detector when detecting
Working Indicator: It is lit when the detector works
Power Switch: Power it on, and the detector works
Smoke output tube: The smoke outlet which connecting with detection port
Power clip: To connect with vehicle battery. The voltage is DC12V.
Pressure gauge: To show the working pressure
Package Includes
1* Main Unit
1* Hook (with hand-tighten nuts)
1* Rubber stopples (with serial specification)
1* Taper stopple
1* Taper pipe
1* 30ml oil bottle
Recent Comments