Top 10 recommendation micro vtx
Finding the best micro vtx suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best micro vtx
1. Wolfwhoop TX3 Micro VTX Only 2.4g 5.8GHz FPV 0.01/25/50/100/200mW Switchable Transmitter FC Uart Support VTX Settings in Betaflight OSD
Feature
Tiny and low weights: under 2.4g0.01/25/50/100/200mW Switchable
0.01mW to prevent adjacent channel interference, Integrated Uart, connectable to betaflight FC
Integrated with FC Uart, connectable to betaflight FC with OSD (Support FC like Wolfwhoop OmnibusF4/OmnibusF4 Pro)
Support parameter remotely adjusted by Betaflight, flight controller, OSD 5V BEC output, support power for receiver and camera
Description
The Wolfwhoop TX3 is a super small, light weight and power switchable VTX support Parameter-adjusting(0.01mW) mode and FC Uart.If you are looking for the cheapest VTX that works perfectly, this is the one to get IMO. Follow up Wolfwhoop, we'll release best vtx at most affordable price.
Save money, fly better.
Feartures:
Supports 40 channels
Tiny and low weights: under 2.4g
Built-in U.FL connector rather than SMA
LC filter allows ultra clean fpv video
0.01/25/50/100/200mW Switchable
Integrated with FC Uart, connectable to betaflight FC with OSD (Support FC like Wolfwhoop OmnibusF4/OmnibusF4 Pro)
Support parameter remotely adjusted by Betaflight, flight controller, OSD 5V BEC output, support power for receiver and camera
0.01mW to prevent adjacent channel interference, Integrated Uart, connectable to betaflight FC
Specification and Parameters:
Input voltage: 3.2-5.5V
FeaturesFC Uart, Parameter-adjusting mode
Power supply: 5V out for camera@ under 300mA max
Output power:
25mW: 300mA @3.7V
50mW: 450mA @3.7V
100mW: 600mA @3.7V
200mW: 650mA @3.7V
Connector: U.FL/IPEX
Dimensions: 19X15(WXD)mm
Weight: 2.4g(excluding antenna)
Package include: 1 X TX3 micro transmitter
1 X U.FL line antenna
1 X JST Cable
1 X user manual
Note :
5645/5925/5945(E4/E7/E8) are not available sue to FCC regulation. Selecting 5645/5925/5945(E4/E7/E8) will be invalid action.
37 channels areall above 5650 and below 5925MHz, which are legalto use in the USA with an amateur radio license.
This equipment is being sold under FCC's amateur radio rules.Operators must require amateur radio license to operator legally in the US. Use of amateur equipment without a
2. Wolfwhoop Q4 5.8GHz VTX with MMCX Antenna Connector and 0.01/25/200/400/600mW 37CH Switchable FPV Transmitter with Smart Audio Support OSD Configuring via Betaflight Flight Controller
Feature
7-24V input with 5V output, Support parameter remotely adjusted by Betaflight, flight controller, OSD, Compatible with betaflight 3.3 and 3.2MMCX has more mating cycles and is more robust
This VTX is that you can mount it on top of your mini FC/PDB stack thanks to the 20x20mm mounting pattern
0.01mW-Power up and test your fpv system during a race with zero interference with any neighbor active channels
FC Uart is basically a feature that allows your to change your VTX settings in Betaflight OSD or even from your Taranis Screen using LUA scripts
Description
It's similar to the Q3 but has a smaller profile that uses 20x20mm mounting pattern, which be designed for smaller micro builds.One cool feature about this VTX is that you can mount it on top of your mini FC/PDB stack thanks to the 20x20mm mounting pattern.
OSD configuration using FC Uart (F3/F4/F7 with OSD)
Built-in BEC: 5V camera @under 300mA
One button frequency and power setup
25/20/400/600mW power switchable
Specification:
Input voltage: 7-24V
Extra features: FC Uart, Parameter-adjusting Mode(0.01mW)
Built-in BEC: 5V camera @under 300mA
Output power:
25mW:100mA @5V
200mW:120mA @5V
400mW:180mA @5V
600mW:220mA @5V
Antenna connector: MMCX
Port connector: JST,6pin
Dimensions: 26(W)X26(D)mm, 20X20mm(hole)
Weight: 4.6g(excluding antenna)
Kit contents: 1XVTX, 1XMMCX pigtail, 1XCable
Note :
5645/5925/5945(E4/E7/E8) are not available sue to FCC regulation. Selecting 5645/5925/5945(E4/E7/E8) will be invalid action.
37 channels areall above 5650 and below 5925MHz, which are legalto use in the USA with an amateur radio license.
This equipment is being sold under FCC's amateur radio rules.Operators must require amateur radio license to operator legally in the US. Use of amateur equipment without a license or use of equipment on restricted frequencies could subject the operator to significant fines by the FCC.By purchasing this equipment, the user is agreeing that they understand these responsibilities and will operate the equipment legally. More information related to ARL, please go tohttp://www.arrl.org/getting-licensed.
3. Wolfwhoop Q8 Nano VTX Integrated OSD 5.8GHz 25/100/200mW Switchable FPV Transmitter with IPEX Antenna for Mini Multicopter
Feature
IPEX line antennaWith 16x16mm hole to hole
built-in OSD, Specifically Designed for the F3
Adjustable 25/100/200mW VTx, 5V power supply for camera
Dimensions: 20mmX20mm (WXD), 16 X 16mm(hole) Perfect match for micro FC
Description
The VTX has built-in OSD, it can display parameters on 5.8GHz goggles or monitors.Specification and Parameters:
Input voltage: 5V
Power supply: 5V camera @ under 0.3A max
Output power: 25mW, 100mW, 200mW
Operating current:
260mA(25mW)
380mA(100mW)
480mA(200mW)
Video format: NTSC
Antenna connector: IPEX
Port connector: JST,6pin
Weight:2g(excluding antenna)
Dimensions: 20(W) X 20(D)mm, 16 X 16mm(hole)
Kit contents: 1 X VTX, 1 X cable, 1 X IPEX linear antenna
Wolfwhoop is never good at brand promotion, the only thing we do is manufacturering.
Wolfwhoop promise that every piece of product you bought from our store is made by Wolfwhoop self-owned factory.
Keep real, keep factory direct.
Save money, fly better.
Please feel free to contact us if you have new ideas for fpv products.
4. Crazepony Runcam TX200U FPV Transmitter 1S 3.5-5.5v 5.8G 48CH 25/200mW Video Transmitter for Nano/Micro Sparrow/Micro Swift 2/Micro Eagle
Feature
[Upgrade Runcam FPV Transmitter]: Add BFCMS control version with flight controller based on Runcam TX200[Stable Performance ]: Long transmission distance and stable transmission, strong clean signal
[Lightweight Design]: Miniature, lightweight and durable,easy to carry
[Easy Operation]: Easy to install, plug and use
[Clear Picture Quality]: Quick light adjustment, clear image in daylight
Description
parameterWorking Current: 5V150~400mA
Video Input Impedance: 75 Ohm
Frequency Channel: 5.8G 48CH
Voltage out: 5Vmax 250mA / Voltage in: 1S 3.5-5.5V
Antenna: U.FL 5.8G 2dB Omni antenna
Lightweight: 2.5g (with antenna), PCB Size: 19mm*19mm
Frequency Setup
Lock mode:
Red LED flashes, only 25mW Bandamp; limited frequency available;
Unlocked mode:
Red LED keeps on, 200mW Bandamp; all 48 channels available; By long pressing button for 10 seconds, you can switch between the two modes.
Note:
Before you get TX200 unlocked, it is highly recommended to know about the rules and regulations in your country about the frequency to avoid a fine or confiscation of your device.
1 Blue LED for Channel
Short press the button to switch the Channel, Channel 1/2/3/4/5/6/7/8 in sequence. For each short press, the Blue LED flashes once, and only when it's under the Channel 1, the LED is always on.
6 Red LED for Band
Long press the button two seconds to switch the Band, Band 1/2/3/4/5/6 in sequence.For each long press, the six Red LEDs light in turn.
1 Orange LED for Power
Long press the button five seconds to switch the power, on is 200mw, o is 25mw, lock mode is limited to 25mw.
Remote control
If you need to get 200mW Bandamp; all 48 channels unlocked, please long press the button on VTX for 10 seconds till the red LED is always on.
Package Including
1 * TX200U Transmitter
1 * Set of screws
5. AKK Nano 1 5.8Ghz 48CH 0mW/25mW/200mW Switchable Micro FPV Transmitter
Feature
0mW/25mW/200mW Micro FPV Transmitter5V output for your camera under 300mA
Setting vtx 0mW power without interference
One button setup channel/band/power
8 RED LED to change channel, 6 BLUE LED to change bands.
Description
Features:
3.2-5.5Vinput voltage
5V output for your cameraunder 300mA
0mW power withoutinterference
0mW/25mW/200mW power switchable
One button setup channel/band/power
8RED LED to change channel, 6BLUE LED to change bands.
Specifications:
Input voltage: 3.2-5.5V
Power supply: 5V Camera @ under 0.3A max.
Output power: 25mW:320mA
200mW:650mA @3.7V
Port connector: 5pin
Antennaconnector: IPEX
Dimensions: 19(W)x15(D) mm
Weight: 2.2g( excluding antenna)
Package includes:
1x FPVtransmitter
1x U.FL antenna
1x Cable
1x Product manual
6. Wolfwhoop Q5 5.8GHz VTX with IPEX Antenna Connector and 0.01/25/50/100/200mW 37CH Switchable FPV Transmitter with FC Uart Support OSD Configuring via Betaflight Flight Control Board
Feature
IPEX has more mating cycles and is more robustYou can do so with the push button on the VTX
0.01mW-Power up and test your fpv system during a race with zero interference with any neighbor active channels
This VTX is that you can mount it on top of your mini FC/PDB stack thanks to the 16x16mm mounting pattern
FC Uart is basically a feature that allows your to change your VTX settings in Betaflight OSD or even from your Taranis Screen using LUA scripts
Description
It's similar to the Q3 but has a smaller profile that uses 20x20mm mounting pattern, which be designed for smaller micro builds.One cool feature about this VTX is that you can mount it on top of your mini FC/PDB stack thanks to the 16x16mm mounting pattern.
OSD configuration using FC Uart (F3/F4/F7 with OSD)
Built-in BEC: 5V camera @under 300mA
One button frequency and power setup
25/50/100/200mW power switchable
Input voltage is 5V, if you want to use with 1S Lipo battery, The package is includes a 3.7V to 5V power booster
Specification:
Input voltage: 5V
Extra features: FC Uart, Parameter-adjusting Mode(0.01mW)
Built-in BEC: 5V camera @under 300mA
Output power:
25mW:100mA @5V
50mW:120mA @5V
100mW:180mA @5V
200mW:220mA @5V
Antenna connector: IPEX
Port connector: JST,6pin
Dimensions: 20(W)X20(D)mm, 16X16mm(hole)
Weight: 2.5g(excluding antenna)
Package included:
1 X VTX
1 X UFL pigtail
1 X power booster
1 X user manual
Note :
5645/5925/5945(E4/E7/E8) are not available sue to FCC regulation. Selecting 5645/5925/5945(E4/E7/E8) will be invalid action.
37 channels areall above 5650 and below 5925MHz, which are legalto use in the USA with an amateur radio license.
This equipment is being sold under FCC's amateur radio rules.Operators must require amateur radio license to operator legally in the US. Use of amateur equipment without a license or use of equipment on restricted frequencies could subject the operator to significant fines by the FCC.By purchasing this equipment, the user is agreeing that they understand these responsibilities and will operate the equipment legally. More information related to ARL, please go tohttp://www.arrl.org/getting-licensed.
7. FPV Transmitter, EACHINE VTX03 Super Mini FPV Transmitter 5.8G 72CH 0/25mW/50mw/200mW Switchable Transmission
Feature
Powering on the VTX, blue LED display 0, indicating the VTX is powered on , but it is in off status without any transmission.Short-press the button to change channel(CH), digital display will change synchronously. Digital display changes cyclically from 1 to 8.Long-press the button for 2 seconds until digital display flicker. Then short-press the button to change the frequency band(FR), digital display will change synchronously. Digital display changes cyclically from A, B, E, F, R, U, O, L, H.
Long-press the button for 5 second until digital display flicker. Then short-press the button to change the power, 25mW/50mW/200mW(one hyphen stands for 25mW, two hyphens stand for 50mW, and three hyphens stand for 200mW).
5 seconds after setting, CH, FR and power will flicker alternately.
NOTE: The VTX has memory for setting. To change the setting, please repeat steps as above.
Description
Specification:Brand name: Eachine
Item name: VTX03 Super Mini FPV Transmitter
Output power: 0/25mW/50mW/200mW switchable (Set output power on 0, to avoid frequency interference)
Input voltage: 3.2-5.5V
5V camera supply, 570mA(MAX)---200mW
5V camera supply, 450mA(MAX)---50mW
5V camera supply, 360mA(MAX)---25mW
Video system: NTSC/PAL
Antenna dimensions: 55mm X 5mm diameter
Antenna: IPEX
Frequency: 5.8GHz 9 bands 72 channels, with Raceband: 5325-5945 MHZ
Size: 21.43*15.20mm(L*W)
Weight: 2.97g
Operation:
-Powering on the VTX, blue LED display 0, indicating the VTX is powered on , but it is in off status without any transmission.
-Short-press the button to change channel(CH), digital display will change synchronously. Digital display changes cyclically from 1 to 8.
-Long-press the button for 2 seconds until digital display flicker. Then short-press the button to change the frequency band(FR), digital display will change synchronously. Digital display changes cyclically from A, B, E, F, R, U, O, L, H.
-Long-press the button for 5 second until digital display flicker. Then short-press the button to change the power, 25mW/50mW/200mW(one hyphen stands for 25mW, two hyphens stand for 50mW, and three hyphens stand for 200mW).
-5 seconds after setting, CH, FR and power will flicker alternately.
NOTE: The VTX has memory for setting. To change the setting, please repeat steps as above.
Package Included:
1 X FPV Transmitter
1 X IPEX antenna
8. AKK KX5 5.8Ghz 25mW/50mW/100mW/200mW FPV Micro Transmitter Support OSD Configuring via Betaflight Flight Control
Feature
25mW/50mW/100mW/200mW/ power switchable5V output for your camera under 300mA
0.01mW support parameter-adjusting mode.
One button setup channel/band/power
OSD configuration using FC Uart (F3/F4/F7 with OSD)
Description
Features:
5V output for your cameraunder 300mA
0.01mW support parameter-adjusting mode.
25mW/50mW/100mW/200mW/power switchable
One button setup channel/band/power with LED display
OSD configuration using FC Uart (F3/F4/F7 with OSD)
Specification:
Input voltage: 5V
Power supply: 5V camera @under 0.3Amax.
Output power:25mW:100mA
50mW:120mA
100mW:180mA
200mW:220mA @5V
Antenna connector: IPEX
Port connector: 6pin
Dimensions: 20(W)X20(D)mm 16x16mm(Hole)
Weight: 2.5g(excluding antenna)
Package includes:
1x X5transmitter
1x U.FL antenna
1x Cable
1x Product manual
9. Wolfwhoop TX1 5.8GHz 48CH FPV 0mW/25mW/200mW Switchable Transmitter with IPEX Line Antenna Mini VTX
Feature
Video system: NTSC/PALMicro size and light weight only 2.2g
Super mini 5.8GHz 408CH FPV transmitter
Suitable for FPV drone, RC car
Specially designed for DIY hobby
Description
The adjustable micro video transmitter with its small form factor and mounted antenna it makes small FPV builds a breeze. Weighing a mere 2.2g makes those lighter builds even lighter.This board has the option to easily connect to a lens board,It's compatible with 5.8GHz receivers. Spektrum, Futaba, FlySky, or any branded receivers.
Specification and Parameters: Input voltage: 3.2-5.5V
Extra features: 0mW(setting VTX without interference)
Power supply: 5V Camera @ under 300mA Max
Output power:
25mW: 320mA @3.7V
200mW: 650mA @3.7V
Antenna connector: IPEX/U.FL
Port connector: 5pin
Dimensions: 19(W) X15(D) mm
Weight: 2.2g(excluding antenna)
Kit included: 1XVTX, 1 UFL antenna
10. Wolfwhoop P-1 Micro 5.8GHz 25mW/50mW/200mW FPV Transmitter and 600TVL AIO Camera with OSD Interface for FPV Quadcopter Drone
Feature
Power by 1S lipo batteryAll in one vtx + camera + antenna, plug and play, ready to fly
Integrated camera and 25mW/50mW/200mW adjustable transmitter
Lighter than WT03, Can be directly connected to osd via Video in/Video out cable
Easy installation for racing drone, button control instead of switches to change channels and bands
Description
Description :
Lighter than WT03, P-1 can be directly connected OSD via V in/V out cable.
The AIO Camera combo is perfect for ultra micro drone. It is a combination of a FPV camera, a transmitter and an antenna. It includes everything into a single unit no bigger than one dollar coin.
It's compatible with branded FPV googles and monitors equipped with 5.8GHz receivers.
Installation is easy and can be done in seconds.
All you need is to put it into your drone and power it by a 1S Lipo battery.
Needed To Complete with 1S Li-Po Battery and 5.8GHz FPV Headset or Monitor.
Specification:
Output power:0/25mW/50mW/200mW adjustable (Set output power on 0, to avoid frequency interference)
Input power: 3.3-5.5V
Current consumption:
250mA-510mA(25mW)
270mA-640mA(50mW)
330mA-740mA(200mW)
Camera resolution: 600TVL
Video system:NTSC
Mini illumination: 1 lux
Field of view: 120
Antenna: dipole brass antenna
Frequency: 5.8GHz 5 bands 40 channels, with Raceband: 5658-5917 MHZ
Size: 19.50*14.00mm(L*W)
Weight: 4.3g
Note: You need to connect the yellow and green wire together if you'er not using the OSD feature. Then red to positive and black to ground. You will need to use the button to set/activate the camera and video transmitter.
Package Included:
1 X P-1AIO FPV Camera (with cable)
1 X User Manual
1 X Cable
Wolfwhoop is never good at brand promotion, the only thing we do is manufacturering.
Wolfwhoop promise that every piece of product you bought from our store is made by Wolfwhoop self-owned factory.
Keep real, keep factory direct.
Save money, fly better.
Please feel free to contact us if you have new ideas for fpv products.
Recent Comments