Top 10 best ramps board 1.5 for 2019
When you looking for ramps board 1.5, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable ramps board 1.5 is not an easy task. In this post, we show you how to find the right ramps board 1.5 along with our top-rated reviews. Please check out our suggestions to find the best ramps board 1.5 for you.
Best ramps board 1.5
1. KINGPRINT Ramps 1.6 Plus Expansion Control Panel with Heatsink Upgraded Ramps 1.5/1.6 for 3D Printer Board
Feature
The PCB has a built-in selection terminal for driving the SPI working mode, and is compatible with STEP/DIR and SPI modesThe power supply and hot bed use 30A high-current terminal block, to avoid the situation of burning terminals to a greater extent
Added a reset expansion interface, convenient for users to extend the reset button
X, Y, Z, E0, E1 all use parallel dual motor interface, so that the board is suitable for more models
Changed the silk screen, making the wiring clear at a glance. Using a combination of colored pin headers and mothers, effectively distinguishing each functional interface, both beautiful and practical
Description
Highlights:
By using the SPI mode, it is only necessary to perform a simple plug-in operation on the jumper cap, which effectively avoids the problem that the motor does not work due to the wrong line insertion, and also prevents the drive from not working and other issues due to poor contact of the external line during the printing process
Tips:
1. Drive mode selection to determine the firmware to be burned, and pay attention to the consistency of the subdivision
2. When using a hot bed with a power greater than 140w, be sure to install the MOS tube heat sink to prevent the mos tube from overheating. When using a hot bed with a power greater than 180w, be sure to select the hot bed MOS module for transfer. Long-term overheating causes the board to be burned
3. When plugging and unplugging the drive to the Ramps1.6+, pay attention to the direction of the drive, never insert it, prevent the drive from being burned, and the operation of the plug drive must be performed under the premise of power failure. We do not bear the loss and consequences of this type of drive and motherboard being burned due to driver insertion errors.
Package Contents:
1x Ramps 1.6 plus
1x heat sink
NOTE:
If you find any problem, please contact us at first, and our technical staff will help you to solve the problem at once. Thanks!
2. BIQU MKS-BASE V1.5 Plate Controller Board for 3D Printer Ramps 1.4
Feature
Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware.4 layers PCB, optimize heat dissipation.
Easy DISPLAY + SD-CARD connector, RepRap Discount SmartController compatible pin header on board.
Up to 5 motor driver with A4982.
Recoverable fuse for short-circuit protection.
Description
Specification:MKS BASE is a feature rich all-in-one electronics solution for Reprap and other CNC devices.
It features an onboard ATmega2560. Its five motor outputs are powered by A4982 stepper drivers.
The board can use the same firmware as Ramps1.4. MKS Base is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.
6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax.
MKS-BASE is suitable for 3D printer manufacturers on batch production, and being used as main control board. Relative to the Ramps1.4, it adds E1 heating output.
MKS-BASE is suitable for dual-Extruder machine.
3. Baosity 32bit Control Board Re-ARM Accessories for Mega 2560 R3 Ramps 1.4 1.5 1.6 3D Printer
Feature
Size: 106*61mmInput voltage: 12V
Power: 200W
Support motor drivers: support A4988 DRV8825 and other motor drivers(support five motor drivers Simultaneously)
Description
Welcome to our store. If you love Sports and Outdoor Activities ,we will provide what you want, and give your much surprise.
Description:
- RE-ARM is a 100Mhz, 32-bit ARM controller with the popular Arduino MEGA footprint.
- It's a plug-in replacement for the Arduino Mega in your RAMPS setup for a quick and easy upgrade to 32-bit goodness.
- It runs Smoothieware and Marlin 2.0 firmwares.
- Easy configuration using a text file on SD card, no need to upload firmware every settings change SD card appear as a drive in windows.
- Support motor drivers: support A4988 DRV8825 and other motor drivers(support five motor drivers Simultaneously)
Specification:
- Size: 106*61mm
- Input voltage: 12V
- Power: 200W
Package Includes:
1x RE-ARM 32-bit control board
4. KINGPRINT NEW 3D Printer Control Board MKS BASE Development Board V1.5 Board RepRap Ramps1.4 Compatible
Feature
Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware.4 layers PCB, optimize heat dissipation.
Easy DISPLAY + SD-CARD connector, RepRap Discount SmartController compatible pin header on board.
Up to 5 motor driver with A4982.
Recoverable fuse for short-circuit protection.
Description
Specification:-MKS BASE is a feature rich all-in-one electronics solution for Reprap and other CNC devices.
-It features an onboard ATmega2560. Its five motor outputs are powered by A4982 stepper drivers.
-The board can use the same firmware as Ramps1.4. MKS Base is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.
-6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax.
-MKS-BASE is suitable for 3D printer manufacturers on batch production, and being used as main control board. Relative to the Ramps1.4, it adds E1 heating output.
-MKS-BASE is suitable for dual-Extruder machine.
Package Included:
1* MKS-Base Controller Board
1* USB Cable
5. KINGPRINT Ramps 1.6 Expansion Control Panel with Heatsink Upgraded Ramps 1.4/1.5 for 3D Printer Board
Feature
This Ramps1.6 controller board is changed the original plug-in MOS tube to patch-type MOS tube.Simple and convenient Connection, larger power than Ramps 1.5/1.4, Better Heat Dissipation with heat sink.
The features of multiple extended interface and replaceable parts make RAMPS1.6 become a control board with powerful upgrade capability and scalable modularity.
It can be extended to LCD and other parts.
There are heater and fan MOSFET outputs and 3 thermistor interfaces
Description
Specification:- The structure almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors, which more simple and convenient to connect, also will not be burnt easily.
- What's more, Ramps 1.6 have a good heat sink above MOS tube in order to give a better function to heat dissipation .
- Besides, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.
- 5A additional security and component protection fusion.
- I2C and SPI pins are available for future expansion.
- Heated bed controls additional 11A fuses
- Support motor drivers: support A4988 DRV8825 and other motor drivers (support five motor drivers simultaneously)
- Power: 12v, 270W
Notice:
1. The heat sink has to be installed when you use this board
2. Don't connect the live board or replace the module interface (except SD,USB)
3. Please press the RESET button or turn off button when emergency
Package include:
1 x Ramps1.6 1 x Heat sink
6. Witbot Ramps1.6 Board Upgraded Ramps1.5 Ramps1.4 Controller Expanding board for 3D Printer
Feature
Optimized and upgraded based on RAMPS1.4, Applied to 5 Pololu stepper drive board(a4988,drv8825 and so on)Higher power, work with heat sink, and easy to use
Patch-type MOS tube, solve the problem of plug-in MOS tube easy to break, take up a large area, poor heat dissipation
It can be extended to LCD and other parts
Design of Pololu plate pin socket can be easily replaced or removed for future design
Description
Description:
This Ramps1.6 controller board is changed the original plug-in MOS tube to patch-type MOS tube in order to solve the problem of plug-in MOS tube easy to break, take up a large area, poor heat dissipation , which can improve the stability and aesthetics of the board. The features of multiple extended interface and replaceable parts make RAMPS1.6 become a control board with powerful upgrade capability and scalable modularity. The controller board can be used when the pins on the back of the board are connected to the Arduino Mega and the front is connected to stepper motor drives
Specification:
1,It can be extended to LCD and other parts.
2,There are heater and fan MOSFET outputs and 3 thermistor interfaces
3,5A additional security and component protection fusion
4,Heated bed controls additional 11A fuses
5,Applied to 5 Pololu stepper drive board
6,Design of Pololu plate pin socket can be easily replaced or removed for future design
7,I2C and SPI pins are available for future expansion
8,Support motor drivers: support A4988 DRV8825 and other motor drivers(support five motor drivers Simultaneously)
9, Power: 12v, 270W
10, Patch MOS tube: B55NF06
Notice:
1,The heat sink has to be installed when you use this board
2, Don't connect the live board or replace the module interface (except SD,USB)
3, Please press the RESET button or turn off button when emergency
Package include:
1 xramps1.6 controller
7. BIQU 3D Printer RAMPS 1.6 Controller Board for Reprap Prusa Mendel Arduino Ramps1.4
Feature
Design of Pololu plate pin socket can be easily replaced or removed for future designThere are heater and fan MOSFET outputs and 3 thermistor interfaces
5A additional security and component protection fusion
Servo connectors are used for connecting limit stops, motors and light-emitting diodes. These connectors are gold-plated and have a rated current of 3A, which is very compact
Heated bed controls additional 11A fuses,Applied to 5 Pololu stepper drive board,I2C and SPI pins are available for future expansion,the LED will light when the heater has output,it can be extended to LCD and other parts,choose 2 motors to connect to Z Prusa Mendell
Description
Product Parameters
Size: 101.5 * 60.5mm
Voltage:12V
Power: 200W
Patch MOS tube: B55NF06
Support motor drivers: support A4988,DRV8825 and other motor drivers(support five motor drivers Simultaneously)
Specification:
RAMPS1.6 is optimized and launched based on RAMPS1.4 by Biqu R & D team
They change the original plug-in MOS tube to patch-type MOS tube in order to solve the problem of plug-in MOS tube easy to break, take up a large area, poor heat dissipation , which can improve the stability and aesthetics of the board
The features of multiple extended interface and replaceable parts make RAMPS1.6 become a control board with powerful upgrade capability and scalable modularity
The controller board can be used when the pins on the back of the board are connected to the Arduino Mega and the front is connected to stepper motor drives
Package Included
1xRamps1.6 3D Control Board
8. Metal Fingerboard Rails (Large Straight) Handmade in The USA for Your Fingerboard ramps and Parks
Feature
LATEST TREND in the sport of fingerboards, finger scooters or finger BMXMADE IN THE USA supporting local entrepreneurs and families
100% GUARANTEE REPLACEMENT at no charge due to manufacturer defects or damage from normal use
STURDY AND LIGHTWEIGHT construction for maximum performance with any of your finger toys
DURABLE ALUMINUM 6061 ALLOY material to help ensure stability and long-lasting fun
Description
Sturdy, lightweight aluminum fingerboard rails. Perfect accessory to your existing fingerboard park. Works great with top fingerboard brands like Flat Face, BlackRiver, Tech Deck and more. Help make your dream fingerboard park come to life!9. BIQU 3D Printer Part SKR V1.3 32bit Control Board Smoothieboard&Marlin Open Source Compatible withRamps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers
Feature
Using 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improvedReserved extended port SERVOS of PWM signal to support BL Touch
Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
The SPI working mode of the TMC2130 driver and the UART working mode driven by the TMC2208, which eliminates complex wiring process and can be used by simple unplugging jumper cap
SKR V1.3 board has CE Certification to adopt 4-Layer PCB with "Gold deposition technology" which capability is more stable and better heat dissipation
Description
Product Description
BIGTREETECH SKR V1.3 motherboard is R&D by Shen Zhen Big Tree Technology CO.,LTD. .The BIGTREETECH SKR V1.3 motherboard not only with a high cost-effective but especially suitable for small and medium-sized 3D printers
How to Work
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port
Https://www.dropbox.com/s/ighnj7oa2l0bm5g/smoothieware-usb-driver-v1.1.exe?dl= 0
2. After installing the driver, connect the computer and SKR motherboard with USB cable
Note: When using smoothieware open-source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! !
3. If you are using Marlin2.0 firmware, follow the tutorial to install:
Tutorial:https://www.dropbox.com/s/ppjfflhf3j5yzh2/MarlinV2.0%20SKRV1.1%20instruction.docx?dl=0
10. BIQU A4988 Compatible Stepper StepStick Motor Diver Module with Heat Sink for 3D Printer Controller Ramps 1.4(Pack of 5pcs)
Feature
A4988 driver board widely used in 3D printers and small CNC machinesSimple step and direction control interface
Thermal protection, over-current protection, ground fault protection
Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage toachieve higher step rates
Description
Specifications:
Size:
A4988:20*15*11mm(LWH)
Heat Sink: 9*9*5mm(LWH)
Weight: 0.8ounces
Color: Red
Features:
-Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
-Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
-Automatic current decay mode detection / selection
-Internal UVLO
-Mixed with slow current decay modes
-Synchronous rectification for low power dissipation
-Crossover-current protection
-Thermal shutdown circuitry
-3.3 and 5 V compatible logic supply
-Thermal shutdown circuitry
-Ground Fault Circuit
-Load short-circuit protection
-Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16
Package Included:
5*A4988 StepStick Stepper Motor Diver Module
5*Heat Sink
Recent Comments