Top 10 best mosaic knife pins 1/4 2019
Finding the best mosaic knife pins 1/4 suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best mosaic knife pins 1/4
1. Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (1/4") (#63 (1/4"))
Feature
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.Diameter: 1/4", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Description
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
2. Mosaic - USA KMS Mosaic Pin for Knife Handle 1/4" x 11" Brass #117-1
Feature
Style #117-1Brass Tube with Stainless Steel Rod and Star Design
Use these mosaic pin/lanyard tubes in your knife handles to give some extra detail.
Description
Tip: These get hot very quickly when being worked and the epoxy will soften or worse break down. This is just the nature of mosaic tubing. Keep them cool when you getting them to length or working them in your handle. Cut or grind them with fresh blade or belt. Dip frequently if you need to.3. 1/4" Diameter Mosaic Knife Handle Pins (Brass/Copper3, 6")
Feature
Custom pins add a refined elegance to your knife handleEach pin is 1/4" in diameter, outside material is brass, inside is copper and brass
This unit is 6" long. Approximately 1" to 3" is used per fastening
Great gift for your custom knives craftsman!
Description
Knife pins hold the scales to the tang, and are an integral part of nearly every knife's handle. While many knives use standard stainless steel pins, sometimes you want your workmanship to stand out, and our custom mosaic pins help you do just that!4. Mosaic - USA KMS Mosaic Pin for Knife Handle 1/4" x 11" Brass #108-1 - Ocean Blue Epoxy
Feature
Style -108-11/4" Diameter x 11" Length
Brass Tubes and Rods with Ocean Blue Epoxy
Description
Use these mosaic pin/lanyard tubes in your knife handles to give some extra detail. Tip: These get hot very quickly when being worked and the epoxy will soften or worse break down. This is just the nature of mosaic tubing. Keep them cool when you getting them to length or working them in your handle. Cut or grind them with fresh blade or belt. Dip frequently if you need to.5. Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (3/16") (#25 (3/16"))
Feature
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.Diameter: 3/16", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Description
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
6. Mosaic Pin 1cm Knife Making Jewelry Handle Scales Grips Knives (#104 Deer Head-Brass)
Feature
NOTICE: Read the "Important Instructions" section below.Diameter: 1cm (approximately 25/64 inches)
Length: 10cm (4 inches)
This pin is made from brass.
Description
It can be used as a solid pin or sliced into thin pieces for inlays. The pattern exists along the entire pin length.
Important Instructions:
- This pin requires a hole of 1cm to be drilled into the handle of your knife. You simply need to use drill bits intended for drilling metal, which are capable of drilling through the steel type of your blade (i.e. hardened 1095 high carbon steel, D-2, stainless, etc).
- Do not expose to excessive heat when cutting the pins (it will become damaged over 95 degrees celsius). Do not polish them too much.
- Use only sandpaper for polishing. Use 1200 grit sandpaper for final polishing.
- And last, use lacquer or oil.
- Outside Diameter: 1cm (equal to 10mm) (approximately 25/64 inches)
- Length: 10cm (4 inches)
- The center of the mosaic pin is filled with epoxy resin.
7. Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (1/8") (#03 (1/8"))
Feature
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.Diameter: 1/8", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Description
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
8. Mosaic pins 5mm dia. Knife DIY parts handle rivets accessories 3
Feature
2pcs lot Mosaic pins 5mm dia. Knife DIY parts handle rivets accessories mosaic pins for knife makingThe listing is for 2 pcs
Total Length: 50mm
Dia: 5mm
9. 3/16" Diameter Aluminum Star Mosaic Pin (11-3/4" Long)
Feature
Made from aluminum, filled with black epoxyDiameter is 3/16" and length is 11-3/ 4"
Mosaic pins are a great way to accent your custom knife handle with details that really make it stand out
NOTE ON SHIPPING: All orders are shipped USPS Priority Mail (1-3 business days) with a tracking number. Amazon automatically combines shipping costs by weight, saving you money
Description
Mosaic pins are a great way to accent your custom knife handle with details that really make it stand out. These pins are machined from aluminum and filled with black epoxy. They are 3/16" in diameter, and approximately 11-3/4 inches long. NOTE ON SHIPPING: All orders are shipped USPS Priority Mail (1-3 business days) with a tracking number. Amazon automatically combines shipping costs by weight, saving you money when you buy multiple items from us during the same check out process.10. Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (7/32") (#42 (7/32"))
Feature
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.Diameter: 7/32", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Description
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
Recent Comments