Top taranis flight controller for 2020
Finding the best taranis flight controller suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best taranis flight controller
1. BETAFPV F4 FC 1S Brushed Flight Controller with SPI Frsky Receiver OSD Smart Audio for FPV Tiny Whoop Micro Racing Drone
Feature
The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.This is a SPI Frsky receiver. Binding easier than before, no need to click the bind button when power on. Manual: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Designed to work with current Tiny Whoop or Blade Inductrix setups
F411 Processor can reach to 100MHz, much faster than the F3 Flight Controller with 72Mhz. Integrated with Frsky receiver only. Upgraded to 30A Lower Resistance MOSFET, Firmware version: betaflight_matekf411rx_3.4.0. Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support Smart Audio.
Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV F4 Brushed Flight Controller Integrated with OSD and Frsky Receiver for Tiny Whoop Drone.
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, SPI Frsky Rx, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.
Binding Procedure--Easier than usual. No need to click the bind button when power on.
a.Power on the board, connecting the battery or USB power. Then the green receiver LED start to flash.
b.Press the bind button for 3s. Then the green receiver LED will be solid on. It means the receiver is in bind mode and you could start to bind your radio transmitter.
Checking here: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
Specifications:
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI Frsky D8 protocol (AKA FRSKY_D on Betaflight Configuration)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.7g
Here is a using video shared by Shutterbug:
https://www.youtube.com/watch?v=M5p2kJGLscU
Package:
1 * F4 OSD brushed flight controller (55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm)
4 * Anti-vibration ruber dampers
2. FrSky Taranis Compatible Receiver X8R 8-Channel 2.4ghz ACCST&RSSI&SBUS Easy to Use Receiver
Feature
1)More number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver.2)Parallel two X8R to become a 16 channel receiver.
3)With RSSI PWM output (0~3.3V)
4)Smart Port enabled, realizing two-way full duplex transmission.
5)FrSky Brand
Description
Model Name:X8R-PCB
Specifications:
Dimension: 46.47*26.78*14.12mm (L *W *H)
Weight: 16.6g
Number of Channels: 16CH (1~8ch from conventional channel outputs, 1~16ch from SBUS port or combine two X8R to become a 16 channels receiver) With RSSI PWM output (0~3.3V)
Operating Voltage Range: 4.0~10V
Operating Current: 100mA@5V
Operating Range: full range (>1.5km)
Firmware Upgradeable
Compatibility: FrSky DFT/DJT/DHT/DHT-U in D_mode FrSky Taranis X9D Plus/XJT in D8 mode
FrSky Taranis X9D Plus/XJT in D16 mode X8R-EU version only works with FrSky Taranis X9D Plus-EU version/XJT-EU version in D16-EU mode.
Features: 1)More number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver.
2)Parallel two X8R to become a 16 channel receiver.
3)With RSSI PWM output (0~3.3V)
4)Smart Port enabled, realizing two-way full duplex transmission.
3. USBasp AVR Programming Device for ATMEL Quadcopter KK2 KK2.X Update Tool by Atomic Market
Feature
Update Your Firmware On Your Quadcopter KK2.x BoardFull Instructions URL On The Package
Takes Less Then 10 Minutes
Programmer Only, KK2 Board Is NOT Included
High Quality Atomic Market Product
4. powerday APM Power Module V1.0 XT60 Female Male Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller
Feature
Max input voltage: 30V , Max current sensing: 90AVoltage and current measurement configured for 5V ADC
Switching regulator outputs 5.3V and 3A max
6-pos DF13 cable plugs directly to APM 2.5's 'PM' connector
Note: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, 3DR radio). It is not designed to power servos. Use your aircraft's own ESC/BEC for that.
5. PolarPro Remote Extension Sticks for The DJI Mavic 2 Pro/Zoom/Air
Feature
Customizable length from 0.75in (stock size) to 1.25 inches for Mavic 2 / Air RemotesGreater height for more precise control over joystick movements
Lightweight machined aircraft aluminum
Compact down to fit inside the remote like the stock sticks
Textured design/finish for enhanced grip
6. 7.4V 2000mAh 8C Rechargeable 2S Lipo Battery for Frsky ACCST Taranis Q X7 Transmitter Remote Controller
Feature
Battery Size:77 x 44 x 11mm, Battery Weight:88 gramUpgrade to 2000mah
8C discharge
Fits For Frsky ACCST Taranis Q X7 Transmitter
7. Radiolink AT10II 12 Channels RC Transmitter and Receiver R12DS 2.4g DSSS&FHSS Remote Controller for RC FPV Drone/Fixed Wing Airplane/Helicopter (Mode 2 Left Hand)
Feature
Excellent Anti-interference: DSSS&FHSS reduce overall signal interference to allow the AT10II to stable transmission signal on all 12 channels, 3ms fast response. Control distance up to 2.5 miles in air.Real-time Information: Real time flight data, model voltage, RSSI signal strength, speed, altitude and more information on the screen when paired with RadioLink's modules(PRM-01/PRM-03).
Adapts to Most of Aircrafts: Takes 1 second to bind to receiver R12DS, it quicks select aircraft models: helicoper, quadcopter, fixed wing, glider, cars, boats and more.
Low Consumption of Battery: Operating amperage of only 105mA (or less). Transmitter can operate for 12 hours with an 1800 mAh LiPo battery. Universal JST(2pin) connector is easily adapted for various battery layouts: AA battery, LiPo, NiMh and more.
Friendly Remind: Low RSSI, radio voltage, receiver voltage and extended engine voltage alarm. DD sounds and words alarming display on the 3.5 LCD screen to avoid ignorance when you are in noise environment.
8. FrSky Upgraded Taranis Q X7S with M7 Hall Sensor Gimbal 16 Channels Transmitter-Carbon Fiber
Feature
Hall sensor M7 gimbal Receiver match Support wireless trainer functionAudio speech outputs (values, alarms, settings, etc.) Real-time flight data logging
Inbuilt wireless trainer system Receiver signal strength indicator (RSSI) alerts
Super low latency Vibration alerts Open source firmware OpenTX installed.
Model files are compatible with TARANIS X9D/X9D Plus/X9E/X7.Support connect the Free Link App for telemetry
9. BETAFPV F4 1-2S AIO FC Brushless Flight Controller SPI Frsky Receiver ESC OSD Smart Audio with JST-PH2.0 Cable for 2S Brushless FPV Whoop Drone Beta85 Pro2 Beta75 Pro2 Beta65 Pro2
Feature
Betafpv F4 2S AIO FC is highly integrated with a Betaflight F411 processor FC, Betaflight OSD, SPI Frsky receiver and 1-2S 5A ESC, suitable for a lighter 2S whoop drone, like Beta65 Pro 2 or Beta75 Pro 2 etc. Saving much weight for a faster fly experienceThe 2S F4 FC AIO Brushless Flight Controller comes with a SPI Frsky receiver, binding procedure is easier than before, no need to click the bind button when power on. Manual: https://betafpv.freshdesk.com/support/solutions/articles/27000049912-f4-1s-brushless-fc-manual
The power supply is 1S~2S, it comes with a 2S cable pigtail JST-PH 2.0 connector in default, you can use 2pcs 1S 300mAh battery work on this. If you want to use it with 2S battery, please change the cable to XT30 : www.amazon.com/dp/B07FFQ2TXQ
The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be seted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode
This AIO F4 2S FC also can be used on 2S brushless whoop drone Beta pro 2 series like Beta85pro2 Beta75pro2 and Beta65pro2, performance very well even no wash-out issue then, so you can just take this AIO FC to replace the stock FC&ESC
10. FrSky Transmitter X9 Lite with Wired Training Function 24 Channels Access Protocol(Glacier White)
Feature
X9 Lite is ACCESS protocol. The receivers should be upgraded to ACCESS protocol to work properly.Compatibility: ACCST D16 and ACCESS receivers
Supports wired training function G7 Noble potentiometer gimbal
Supports spectrum analyzer function Haptic vibration alerts and voice speech outputs
High-speed module digital interface Easily accessible battery compartment (*Batteries not included, adaptive with replaceable 18650 button top Li-ion batteries)
Recent Comments