Top 10 lathe chuck spacer for 2020
What are criterias of the best lathe chuck spacer? It is not easy to find the answer. We spent many hours to analyst top 10 lathe chuck spacer and find the best one for you. Let’s find more detail below.
Best lathe chuck spacer
1. Norton Bench and Pedestal Abrasive Wheel, Type 01 Straight, Aluminum Oxide, 1" Arbor, 8" Diameter, 1" Thickness, Fine Grit (Pack of 1)
Feature
Each wheel contains arbor bushings in sizes 5/8", 3/4", and 7/8"2. 4" Steel Wood Lathe Face Plate, 1-1/4" x 8tpi Threaded
Feature
7/16" Thick Steel Faceplate - Heavy and Rigid. 1-1/4" Thread DepthLocking set screw for use on reversing lathes
Some Powermatic & Laguana lathes may require Maxwood 5144 spacer behind this faceplate (extra long spindle on these)
3. 6" Steel Wood Lathe Face Plate, 1-1/4" x RH 8tpi Threaded with set screw to lock on spindle for reverse turning
Feature
7/16" Thick Steel Faceplate - Heavy and Rigid, 1-1/4" Thread Depth8 Offset Screwholes on 2 guide rings for easy centering
Locking set screw for use on reversing lathes
Flat spots cut on back spigot for easy removal from lathe
Some Powermatic & Laguana lathes may require Maxwood 5144 spacer behind this faceplate (extra long spindle on these)
4. PSI Woodworking Products LCENTSET 7-Piece Multi Spur Drive Center Set With A 1-Inch by 8 TPI Mount
Feature
Includes (3) 4-prong Spur Centers, (3) Multi-tooth Super Centers, (1) 1" x 8tpi threaded Center Carrier, and (1) set of Tightening LeversBoth center types come in 5/8", 1", and 1-1/2"
All centers have a spring loaded pin for easy mounting and removal of your work-piece
Thread the 1" x 8tpi Center Carrier onto your lathe's headstock spindle for easy insertion and removal of all the centers
Comes in wooden case for storage
5. PSI Woodworking PKMSTS1 Live Tailstock Mandrel Saver #1 Morse Taper
Feature
Unique design to support the end of your penturning mandrelProvides no pressure on the tailstock end of the mandrel shaft thus eliminating any bending or vibration
There is no longer a need for spacer bushings
Will work with all mandrels with a diameter of 0. 245" or less
Compatible with lathes that accept #1MT accessories in tailstock
6. PSI Woodworking PKMS2SET Pen Mandrel Saver Package, 2 Morse Taper (2MT)
Feature
Includes 7mm drill bit, (5) 7mm bushings, #2MT mandrel saver tailstock center, & #2MT basic mandrel.Perfect system to avoid bent mandrel shafts and ruining the point on your live center.
System adapts to the length of your project.
No need for the knurled nut that sometimes gets lost, misplaced, or stripped.
Great for turners of all Skill levels.
7. PSI Woodworking CF4 Lathe Faceplate for 3/ x 16 tpi Spindle, 4" Without Screwchuck
Feature
Country Of Origin: ChinaModel Number: CF4
Item Package Dimension: 4.75" L x 1.5" W x 4.75" H
Item Package Weight: 1.8 lb
8. PSI Woodworking PKMJAM Mandrel Jam Chuck System with No.2 Morse Taper
Feature
Use for mounting and fastening wooden spindles for turning the outer surfacesIdeal for turning Peppermill blanks, Kaleidoscope blanks, and any other project blank that has a completely drilled-thru hole of 1", 1-1/2", or 2"
Includes (1)9" threaded mandrel shaft 3/8"x16tpi , (1)#2MT arbor, (3)sets jam chuck wheels 1",1-1/2",2" diameter, (3)sets washers, (6)lock nuts 3/8"x16tpi, (1)tightening wrench, (4)spacer bushings
For support, lock the tailstock in place with a 60 Degree live center
The system holds a spindle up to 7" long
9. MAXWOOD 5144 1/4" THICK BUSHING FOR LONGER 1-1/4" LATHE SPINDLES TO ACCEPT MAXWOOD 5107 AND 5114 FACEPLATES
Feature
1/4" Thick x 1-1/4" center x 2-1/8" ODFor using Maxwood 5107 and 5114 faceplates on lathes with longer spindles
Especially recommended for some Powermatic and Lagauna lathes
10. Laguna Tools Revo Lathe 110v 1.5HP 18"/36" Induction 1725RPM Motor w/Variable Speed Frequency Drive Model MLAREVO 1836-110
Feature
Electrical: 1. 5HP, 110 volt, 60 HzMotor: induction, 1725 RPM, TEFC
Pfd: Delta S1 variable frequency drive
Phase: 1 Phase input, 3 phase output
Poly-groove drive belt with EZ Access
Recommended breaker: 15 amp
Spring loaded spindle lock
Max outboard swing: 32
Swing over BANJO: 13 1/2
Steel bed: ASTM A36
Recent Comments