Best arduino battery list

We spent many hours on research to finding arduino battery, reading product features, product specifications for this guide. For those of you who wish to the best arduino battery, you should not miss this article. arduino battery coming in a variety of types but also different price range. The following is the top 10 arduino battery by our suggestions:

Best arduino battery

Product	Features	Editor's score	Go to site
	MakerFocus 4pcs 3.7V Lithium Rechargable Battery, 802540 3.7V 1000mAh Battery with Protection Board Insulated Rubber Tape Matched with ESP32 Development Board WIFI Kit for Arduino Nodemcu		Go to amazon.com
	energyShield 2 Basic - Rechargeable Battery for Arduino		Go to amazon.com
	Adafruit 328 Battery, Lithium Ion Polymer, 3.7V, 2500mAh, 2" x 2.55" x 0.30" Size		Go to amazon.com
	Gikfun 9v Battery Holder with ON/OFF Switch for Arduino (Pack of 2PCS) EK2107x2		Go to amazon.com
	5pack 9v Battery Clip with 2.1mm X 5.5mm Male DC Plug for Arduino by Corpco		Go to amazon.com
	Gikfun Plastic Battery Storage Case Holder For 4 X AA and 2 X AA wire leads Arduino EK8304		Go to amazon.com
	Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger - v1 [ADA1904]		Go to amazon.com
	Generic 4xAA Battery Holder to DC Barrel Jack Connector for Arduino(pack of 2)		Go to amazon.com
	AspenTek 9v Battery Clip Snap Accessories with 2.1 X 5.5mm Male Dc Plug for Arduino(5 Pack)		Go to amazon.com
	Uno R3 (Open-Source Clone of Arduino Uno R3), USB Cable, 9V snap Connector, and 8AA Battery Pack (Batteries not Included).		Go to amazon.com

Related posts:

1. MakerFocus 4pcs 3.7V Lithium Rechargable Battery, 802540 3.7V 1000mAh Battery with Protection Board Insulated Rubber Tape Matched with ESP32 Development Board WIFI Kit for Arduino Nodemcu

Feature

[Note1]: After some customers reflected the reversed connectors, we have modified the connectors now, so all the new batteries are correct correct polarity now, you don't need to switch the polarity of the two wires. Thanks a ton for every customer's suggestion and support.
[Note2]: The maximum operating current of this battery is only about 1A, cannot be used for unmanned aerial vehicles, model aircraft or power tools and other products that require high current.
[Usage]: This product interface is 1.25 pitch male, it can be matched with ESP32 Development Board WIFI Kits for Arduino Nodemcu.
[Standard Charging Method]: Charging this battery to 4.25V at 0.2C constant current, then charge the battery at a constant voltage of 4.2V till it's charging current 0.05C. Working Current: 1.5A
[Charge current time]: Standard Charging: 0.2C (8 hours); Fast charging: 0.5C (2.5 hours).

Description

4pcs 3.7V Lithium Rechargable Battery, 852540 3.7V 1000mAh Battery with Protection Board andamp; Insulated Rubber Tape Matched with ESP32 Development Board WIFI Kits for Arduino Nodemcu

Features:
1. Note: The maximum operating current of this battery is only about 1A, can not be used for unmanned aerial vehicles, model aircraft or power tools and other products that require high current.
2. This product interface is 1.25 pitch male, it can be matched with ESP32 Development Board WIFI Kits for Arduino Nodemcu.

Specification:
Standard Voltage: 3.7V
Rated Capacity: 1000mAh
Weight: About 17g
Size: 8.5*25*40mm
Working Current: 1.5A
Overcurrent protection: 2~3A
Overcharge limit pressure: 4.250.05V
Over-voltage limit pressure: 2.450.30V

Standard Charging Method: Charging this battery to 4.25V at 0.2C constant current, then charge the battery at a constant voltage of 4.2V till it's charging current 0.05C.
Charge current time: Standard Charging: 0.2C (8 hours); Fast charging: 0.5C (2.5 hours).
The maximum charging current: 0.5C
Continuous Dishcarge Current: 0.5C
The maximum discharge current: 1C
End-off voltage: 2.75V/pcs
Allowable charging temperature: 0 ~ +45
Allowable discharge temperature: -10 ~ +60
Allowable storage temperature: -10 ~ +40 ( within 3 months); -10 ~ +30 ( within 6 months).

Package Including
4 * 1000mAh 852540 3.7V Lithium Rechargable Battery

2. energyShield 2 Basic - Rechargeable Battery for Arduino

Feature

RECHARGEABLE LI-ION BATTERY - The energyShield 2 Basic has an 1800mAh lithium-ion battery at its core, protected with an impact-resistant, injection molded, ABS cover
USB CHARGING - The battery can be recharged from any USB port with a micro USB cable
ADD MOBILITY - With the built-in power source, projects made with the energyShield 2 Basic can be moved around freely, without the USB/power cable tethering you to your desk
MULTIPLE POWER OUTPUTS - The energyShield 2 Basic power circuitry provides both 5V (1000mA) and 3.3V (300mA)
ARDUINO SHIELD FORM FACTOR - All of the functionality of the energyShield 2 Basic is packed inside of a standard Arduino shield, which will fit right into your stack

Description

Product Description

The energyShield 2 Basic is an elegant power solution for any electronics project. It is a simplified version of the energyShield 2 Pro that provides battery management and voltage regulation for a low cost. It provides 5V and 3.3V outputs at currents up to 1000mA and 300mA, respectively. These supplies are powered by the included 1800mAh (6.7 Wh) lithium-polymer battery which can be charged via USB. The battery is fully enclosed in an impact-resistant, injection molded, ABS cover to prevent any damage to the lithium polymer cell. The energyShield 2 Basic is a great pair with any Arduino platform, allowing the user to power their project anywhere.

Features

1800mAh Lithium-Ion Battery Included with Protective Case
USB Charging (microB)
5V (1000mA) and 3.3V (300mA)
Fully Assembled
Arduino Compatible Shield

3. Adafruit 328 Battery, Lithium Ion Polymer, 3.7V, 2500mAh, 2" x 2.55" x 0.30" Size

Feature

Size: 2" x 2.55" x 0.30"
Output: 2500Mah at 3.7V nominal
Output connector: jst wire to board (2Mm pitch)
Compatibility: feather huzzah with Esp8266 wifi and feather huzzah with Esp8266 wifi starter kits. Polarity matches all Adafruit LiPoly/LiIon chargers and boards, other brands may have reverse polarity and can destroy your battery. As with all Lithium ion polymer batteries and with any power source - they should be used by experts who are comfortable working with power supplies.
Not compatible with PS4 (Does not fit in controller).

Description

Lithium ion polymer (also known as 'LiPO' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for total power of about 10 WH. The batteries come pre-attached with a genuine 2-pin jst-ph connector as shown and include the necessary protection circuitry. Because they have a genuine jst connector, not a knock-off, the cable won't snag or get stuck in a matching jst jack, and they click in and out smoothly. The included protection circuitry keeps the battery voltage from going too high (over-charging) or low (over-use) which means that the battery will cut-out when completely dead at 3.0V. It will also protect against output shorts. However, even with this protection it is very important that you only use a liion/lipoly constant-voltage/constant-current charger to recharge them and at a rate of 1200MA or less. Like most lipos, the batteries we sell do not have thermistors built in. This is why we suggest charging at 1/2C or even less - 1200MA max in this case. Even 500MA is a good charge rate, which is how much you can get from a USB port.

4. Gikfun 9v Battery Holder with ON/OFF Switch for Arduino (Pack of 2PCS) EK2107x2

Feature

9v Battery Holder with ON/OFF Switch 9 Volt Box Pack Power Toggle for Arduino
Pack of 2pcs

Description

2pcs 9V battery With cover and ON/OFF switch

5. 5pack 9v Battery Clip with 2.1mm X 5.5mm Male DC Plug for Arduino by Corpco

Feature

Plug Type: 2.1mm x 5.5mm Male to 9V Battery Clip
Cable length:6 inches
Great to use for LED strip light or arduino
Package contains 5 pcs 9v Battery Clips (9V battery is not included)
Arduino and Battery shown for example only

Description

Make your Arduino projects portable with these 9V battery snaps powering your project. Standard 2.1mm x 5.5mm center positive male plug connects directly to the Arduino board. Our battery adapters are covered by a 90 day warranty.

6. Gikfun Plastic Battery Storage Case Holder For 4 X AA and 2 X AA wire leads Arduino EK8304

Feature

1PC Plastic Battery Storage Case Box Holder For 4 X AA 4xAA 2A 6.0V wire leads
1PC Plastic Battery Storage Case Box Holder For2 X AA 2xAA 3V with wire leads

Description

1PC Plastic Battery Storage Case Box Holder For 4 X AA 4xAA 2A 6.0V wire leads
1PC Plastic Battery Storage Case Box Holder For2 X AA 2xAA 3V with wire leads

7. Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger - v1 [ADA1904]

Feature

Battery not included

Description

Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger - v1 Adafruit Product ID: 1904. Battery not included.

8. Generic 4xAA Battery Holder to DC Barrel Jack Connector for Arduino(pack of 2)

Feature

The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector
The connector mates with the barrel jack on the Arduino (among a number of other products) allowing you to easily make your project battery powered

Description

Description:
This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector.
The connector mates with the barrel jack on the Arduino (among a number of other products) allowing you to easily make your project battery powered.
Note:
The average voltage regulator has about 1V of dropout (but can vary greatly). This pack, with normal alkaline batteries, will output ~5.5V causing a normal 5V board to run at around 4 to 4.5V. This depends a lot of what board and processor you are using with the battery pack. Please consult yer datasheet.

9. AspenTek 9v Battery Clip Snap Accessories with 2.1 X 5.5mm Male Dc Plug for Arduino(5 Pack)

Feature

Plug Type: 2.1 x 5.5mm Male to 9V Battery Clip
Length:12cm 4.72 inch
Material(External): Plastic and copper wire
Great to use for LED strip light or arduino
Package Included 5 pcs 9v Battery Clips (9V battery is not included)

Description

9V Battery Connector 9V battery clip for arduino

Snap-on terminal for 9-VOLT active pickup systems or for DIY USE

Package Included:5 pcs 9v Battery Clips (9V battery is not included)

10. Uno R3 (Open-Source Clone of Arduino Uno R3), USB Cable, 9V snap Connector, and 8AA Battery Pack (Batteries not Included).

Feature

ATmega328P SMD chip with CH340G USB driver. Plug and play with Windows 10 and the Arduino IDE.
Power the Uno R3 with a 9V battery or the 8AA battery pack (batteries not included).
8 AA rechargable batteries provide 9.6V of power. 8 AA alkaline batteries provide 12V of power. Perfect match for the recommended 7-12V input.
Includes open-source Arduino Uno R3 clone, USB cable, 9V snap connector with barrel jack plug, and 8AA battery pack (batteries not included).
Compatible with Arduino Uno R3

Description

Compatible open-source clone of the Arduino Uno R3, USB cable, 9V snap connector, and 8AA battery pack (batteries not included). Power the Arduino with a 9V battery or use the 8AA battery pack (batteries not included). 8 rechargable AA batteries provide 9.6V. 8 alkaline batteries provide 12V. Recommended input voltage for the Arduino is 7-12V, so the battery pack is in the ideal voltage range. The Uno R3 uses the ATmega328P SMD chip and the CH340G USB driver. On Windows 10, just plug in the USB cable, launch the Arduino IDE, and this device will appear on second COM port.

Conclusion

By our suggestions above, we hope that you can found the best arduino battery for you. Please don't forget to share your experience by comment in this post. Thank you!