arduino stepper motor driver sheild buyer’s guide
Shopping arduino stepper motor driver sheild has never been easy. You may come many of website, read arduino stepper motor driver sheild reviews, check the price… It will really makes you headache and tired. Don’t worry! I’ve found ways to make it less painful. Let’s find in below article.
Best arduino stepper motor driver sheild
1. KEYESTUDIO UNO R3 CNC Kit/CNC Shield V3.0 +4pcs A4988 Stepper Motor Driver + UNO R3 ATmega328P with Usb Cable for Arduino GRBL Compatible
Feature
Uno R3 Board for Arduino: USB-TTL used ATMEGA 16U2 chip, controller used ATMEGA 328P chipUS ATMEL original, fast transfer and more memory:), the same circuit arrangement and work as originalLatest Arduino CNC Shield Version 3.0: grbl compatible (open source firmware that runs on an arduino uno that turns G-code commands into stepper signals) 4-Axis support; jumpers to set the micro-stepping for the stepper drivers; runs on 12-36V DC
A4988 Stepper Motor Driver: simple step and direction control interface; thermal shutdown circuit/cross current/ground fault/short circuit protection, five step modes; voltage: 3.3v and 5v; mix with slow current attenuation model etc
FCC and CE certification: this high quality arduino cnc kit is well packaged, solder is very clean, everything is aligned nicely, has made function,voltage, current testing before packaging
It is really safe and great choose for engraver 3d printer manufacturer, arduino learner and diy machine lover
Description
Specification:(1)3D Printer CNC Shield Board V3.0
GRBL compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total) Spindle enable and direction Coolant enable
Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
(2)A4988 Stepper Motor Driver
Thermal shutdown circuitry:Yes
Crossover-current protection:Yes
Ground fault protection:Yes
Load short-circuit protection:Yes
Compatible logic supply: 3.3V and 5 V
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Features:
1.Mix with slow current decay modes.
2.Internal UVLO and Low RDS (On) Output.
3.Automatic current decay mode detection/selection.
4.Synchronous rectification for low power dissipation.
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver)
(3)Uno r3 Board For Arduino(more details please search the asin B0168B39N4)
Package Included:
1 x Arduino R3 Development Board
1 x Engraver CNC Shield Board
4 x A4988 Stepper Motor Driver
1 x 30 cm USB Cable
2. kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver With Heatsink for Arduino Kits K75 (CNC Shield+UNO R3+Stepper Motor)
Feature
LatestCNCShieldVersion3.0forArduinoArduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC
2 x End stops for each axis (6 in total)
4pcs A4988 Stepper Motor Driver with radiator
Description
CNC Shield Board:Latest Arduino CNC Shield Version 3.0
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC
Arduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader - included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHz
A4988 Stepper Motor Driver:
A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection;
Low RDS (On) Output
Automatic current decay mode detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Crossover-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble).
PackageContents:
1xCNCShieldBoard
1xUNOR3BoardforArduino
4xA4988StepperMotorDriver
4xHeatSink
3. KEYESTUDIO CNC Diy Kit-GRBL CNC Shield V3+4pcs DRV8825 Stepper Motor Driver+Usb Cable+Uno R3 Controller for Arduino
Feature
Excellent uno r3 board with atmega 16u2 chip and atmega 328p chipUS ATMEL original, fast transfer and more memory)Latest keyestudio cnc shield version 3.0, grbl 0.8c compatible, 4-Axis support, runs on 12-36V DC
Simple step and direction control interface DRV8825 drivers, six different step resolutions, adjustable current control, intelligent chopping control, built-in regulator, etc
They are well packaged and got FCC and CE certification, solder is very clean, everything is aligned nicely, has been made function,voltage, current testing before packaging
This is hardware & software included diy cnc controller kit, just scan the qr code on the picture to get the wiki tutorial to know more information and download the software
Description
(1)CNC shield v3 for ArduinoIt has 4 channel slots for DRV8825 stepper motor driver modules, 6 IO ports is sufficient to manage 3 stepper motors
GRBL 0.8c compatible. 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Spindle enable and direction
Coolant enable
Uses removable Pololu DRV8825 compatible stepper drivers. (A4988, DRV8825 and others)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
Compact design
Stepper Motors can be connected with 4 pin molex connectors or soldered in place
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board)
(2)4pcs DRV8825 Driver
It operates from 8.2-45V and can deliver up to approximately 1.5A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling)
Suitable for driving stepper motors within 8.2V~45V 2.5A
Simple step and direction control interface;
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step;
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout;
Short-to-ground and shorted-load protection
(3)Uno r3 Board For Arduino(more details please search the asin B0168B39N4)
List
CNC Shield V3.0 *1
Uno R3 Board *1
DRV8825 Driver *4
USB Cable *1
4. Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit
Description
This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well. Completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project. Lets check out these specs again: 2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter! 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. Motors automatically disabled on power-up Big terminal block connectors to easily hook up wires (18-26AWG) and power Arduino reset button brought up top Polarity protected 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies Tested compatible with Arduino UNO, Leonardo, ADK/Mega R3, Due, Diecimila & Duemilanove. Works with Mega/ADK R2 and earlier with 2 wire jumpers. Download the easy-to-use Arduino software library, check out the examples and you're ready to go! Comes with an assembled & tested shield, terminal block, plain header, jumper. Some soldering is required to assemble the headers on. Stacking headers not included.5. Arduino A000079 Motor Shield, R3, 5V to 12V
Feature
Operating voltage: 5V to 12VMotor controller: l298p
Drives 2 dc motors
Description
Arduino A000079 Motor Shield, R3, 5V to 12V. Operating voltage: 5V to 12V. Motor controller: l298p. Drives 2 dc motors. Arduino A000079 Motor Shield, R3, 5V to 12V. Unit Count : Motor.6. WINGONEER L298P Motor Driver Module H-bridge Drive Shield Expansion Board High-Power DC Stepper Motor Controller For Arduino
Feature
Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2AUse eight high-speed Schottky diodes at motor output as protection
Stack design can be directly plugged into the Arduino, easier to use
The L298P shield DC motor driver has PWM speed control mode; dual high-power H-bridge driver
Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input
Description
WINGONEER trademark Reg.NO:4747611Technical Specifications:
1 logical part of the input voltage VD: 5V
2driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input
3 logical part of the work current Iss: <36mA
4.driven part of the operating current Io: <2A
5 maximum power dissipation: 25W (T = 75 Celsius)
6. control signal input level: High 2.3V low -0.3V
7 Working temperature: -25 + 130 Celsius
8 hardware interface: 5.0mm pitch terminal
9 belt clip and can be controlled via front row access signal
10. Drive Type: Dual power H-bridge driver
11 Pin occupancy: D4 ~ D7 direct drive motor
12 supports PWM / PLL mode motor speed control
13 Size: 68 * 53mm
Packing included:
1 x WINGONEER L298P Motor Driver Module
7. HiLetgo V3 Engraver Shield 3D Printer CNC Expansion Board A4988 Driver Board for Arduino (Pack of 2PCS)
Feature
Using A4988 moduleFive different step mode
Adjust the maximum current output, so as to obtain a higher rate of step.
Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals
Can drive four A4988 stepper motor
Description
V3 Engraver Shield 3D Printer CNC Expansion Board A4988 Driver Board for Arduino Description:100% brand new and high quality
This expansion board as a driver expansion board can be used for engraving machines, 3D printers.
It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use.
UNO for Arduino module IO port correspondence introduction.
8. Qunqi L293D Motor Drive Shield For Arduino Duemilanove Mega UNO R3 AVR ATMEL
Feature
L293D is a monolithic integrated, high voltage, high current, 4-channel driverBasically this means using this chip you can use DC motors and power supplies of up to 12 Volts
The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
Thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what's known as a type of H-Bridge.
Can drive 4 DC motors or 2 stepper motors or 2 Servo.
Description
Specification:1.Up to 4 bi-directional DC motors with individual 8-bit speed selection.
2.Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
3.4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 12V DC.
4.Pull down resistors keep motors disabled during power-up.
5.2 external terminal power interface, for seperate logic/motor supplies.
6.Tested compatible for Arduino Mega, Diecimila & Duemilanove.
Package include:
1x L293D Motor Drive Shield
9. kuman L293D Motor Drive Shield Expansion Board For Arduino Duemilanove Mega UNO R3 AVR ATMEL KY58
Feature
Kuman L293D Motor Drive Shield expansion board can drive 2 stepper motors or 2 Servo or 4 DC motorsWidely compatible: L293D Motor Drivecompatible for Arduino Mega, Diecimila and Duemilanove, meet you need at most
2 external terminal power interface, for seperate logic/motor supplies
4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 25V DC
L293D Motor Drive Shield is a monolithic integrated, high voltage, high current, 4-channel driver
Description
Features :2 interface for 5V Servo connected to the Arduino"s high-resolution dedicated timer - no jitter.
Can drive 4 DC motors or 2 stepper motors or 2 Servo. Up to 4 bi-directional DC motors with individual 8-bit speed selection.
Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 25V DC.
Pull down resistors keep motors disabled during power-up. 2 external terminal power interface, for separate logic/motor supplies. Compatible for Arduino Mega, Diecimila and Duemilanove
Specifications:
Type:Module
Module Function:Board
Operating Voltage : 5V~12V
Current Sensing : 1.65V/A
Max current : 2A per channel or 4A max (with external power supply)
You will get:
1* L293D Motor Drive Shield, friendly customer service
10. WINGONEER PWM Servo Driver Module 16 Channel 12-bit PWM Servo Drive Shield Board For Arduino EK1690
Feature
I2C input, 16-channel PWM servo driver module, driving 16 servos.Rudder power supply Independent V + input, max. 6V.
Logic signals and logic power independent output, 3-5v.
Frequency 40-1000 Hz.
Number of channels: 16 channels, resolution: 12 bits.
Description
WINGONEER trademark Reg.NO:4747611WINGONEER PWM Servo Driver Module 16 Channel 12-bit PWM Servo Drive Shield Board For Arduino EK1690
Description:
I2C input.
16-channel PWM servo driver module, driving 16 servos.
Rudder power supply Independent V + input, max. 6V.
Logic signals and logic power independent output, 3-5v.
Frequency 40-1000 Hz.
Number of channels: 16 channels.
Resolution: 12 bits.
Size:69*53.5*23.3mm/2.71*2.11*0.92in(L*W*H).
Weight:20.3g/0.72oz.
Pack include:
1x WINGONEER PWM Servo Driver Module 16 Channel 12-bit PWM Servo Drive Shield Board For Arduino EK1690
Recent Comments